background image

 

 

www.advancedco.com 

2.3  PCB Mounting in a 4200 / 4400 Panel 

 

The card may be fitted to the chassis 
using 4x M3 screws. Refer to Figure 3 
opposite. 

Screws marked 

*

 must be securely 

fixed to provide an earth connection for 
EMC purposes. 

Where the unit is used for lightly 
loaded outputs, the power may be 
supplied by the AUX 24VDC panel 
supply output. 

In this case, check and ensure that the 
power supply and battery standby can 

support the application. 

 

Base Card 

DC SUPPLY 
(Max 500mA!) 

Communications 

M3 Fixing 
Screws 

TB3 

TB2 

4-Way Relay 

 

FIGURE 3 

Wiring should be in accordance with subsequent sections of this manual. 

Refer to FIGURE 3 above for the recommended routing of cables. 

 

2.4  PCB Mounting in a 5000 Panel 

There is provision on the 5000 chassis plate to mount one peripheral bus module (except 5100 small 
enclosure). Refer to panel manual 680-165 for further information. 

2.5  DIP Switch Configuration 

Each 4-Way Relay Card must be given a unique 
address. 

The interfaces are added to the configuration 
file in the PC CONFIG tool at Peripheral Bus 
Address 66-81. 

The DIP Switch on each unit must be set 
accordingly to the corresponding address 
defined. See table opposite. 

 

OFF 

ON 

 

Address 

SW1-1 

SW1-2 

SW1-3 

SW1-4 

66 

OFF 

OFF 

OFF 

OFF 

67 

ON 

OFF 

OFF 

OFF 

68 

OFF 

ON 

OFF 

OFF 

69 

ON 

ON 

OFF 

OFF 

70 

OFF 

OFF 

ON 

OFF 

71 

ON 

OFF 

ON 

OFF 

72 

OFF 

ON 

ON 

OFF 

73 

ON 

ON 

ON 

OFF 

74 

OFF 

OFF 

OFF 

ON 

75 

ON 

OFF 

OFF 

ON 

76 

OFF 

ON 

OFF 

ON 

77 

ON 

ON 

OFF 

ON 

78 

OFF 

OFF 

ON 

ON 

79 

ON 

OFF 

ON 

ON 

80 

OFF 

ON 

ON 

ON 

81 

ON 

ON 

ON 

ON 

 

Summary of Contents for Mxp-035













Reviews: