ENGLISH
ING Series
| User manual
10
11
Series
User manual
|
ING
Series
press again ESC (ING 30R) or SET (ING 20R) to exit the menu.
Simultaneously using more systems, it’s better to have them on the same group
but on different channels.
If the transmitter is in Mono mode, using the up/down buttons you set the position
of the signal in the Stereo field.
4 TONE SELECTION (ING 30T only)
Press the SET button for 2 seconds to access the settings menu, then press again
SET until when “TONE” starts flashing in the display. Use the up and down buttons
to activate (ON) or deactivate (OFF) TONE feature.
TONE ON boosts high frequencies.
5 LIMITER SELECTION (ING 30T only)
Press the SET button for 2 seconds to access the settings menu, then press again
SET until when “LIMITER” starts flashing in the display. Use the up and down buttons
to activate (ON) or deactivate (OFF) LIMITER feature. LIMITER ON reduces sudden
peaks, thus protecting your hearing.
6 LOCK (ING 30T only)
Press the SET button for 2 seconds to access the settings menu, then press again
SET until when the lock icon starts flashing. Use the up and down buttons to activate
(ON) or deactivate (OFF) the lock.
ATTENTION: when LOCK icon is displayed, you can see the unit settings, which
are not editable.
7 MIX (ING 30T only)
Press the SET button for 2 seconds to access the settings menu, then press again
SET until when “MIX” starts flashing in the display. Use the up and down buttons to
activate (ON) or deactivate (OFF) MIX feature.
MIX ON allows to listen both transmitter input signals - AF1 and AF2 - using the
supplied earphones.
To balance the signal between AF1 and AF2 inputs, press the up and down buttons.
You can choose among 31 available positions:
In MIX -0- position, AF1 and AF2 input signals are balanced.
Press the (button arrow up) to increase AF1 signal versus AF2 signal:
1-, 2-, 3-, 4-, 5-, 6-, 7-,8-, 9-, A-, b-, C-, d-, E-, and F- (max)
Press the (button arrow down) to increase AF2 signal versus AF1 signal:
-1, -2, -3, -4, -5, -6, -7, -8, -9, -A, -b, -C, -d, -E, and -F (max)
8 BATTERIES LEVEL INDICATOR
This icon displays in 4 steps the battery charge level. When inside the icon there’s no
bars present and LOW BATT LED flashes, please immediately replace the batteries.
4
|
TROuBLESHOOTING
PROBLEM
LEDS
SOLuTION
No sound or very
low sound level.
Power LED
turned off.
Make sure the batteries are not discharged
and that the receiver is turned on.
Transmitter LCD turned off.
Check the connection between power
supply and the transmitter.
Turn on the transmitter.
Receiver RF indicator is off.
Make sure that transmitter and receiver are
set to the same frequency.
Reduce the distance between transmitter
and receiver, and verify that the two devices
are in direct visual contact.
Make sure that the transmitter antenna is
mounted correctly.
Receiver turned on
and RF light on.
Raise the volume of the receiver and check
earphones connection.
Check the input level of the transmitter and,
possibly, increase it.
Distortions or unwanted
interferences.
Receiver RF
antenna lit.
Increase the distance from possible causes
of interference (digital control devices, such
as CD player, console ...).
Use a different frequency.
Distorted sound.
Receiver LOW
BATT LED
flashes.
Too high level
indicator of the
transmitter.
Replace the batteries.
Turn down the volume control of the
transmitter or the volume of the source
device.
Listening to a Mono signal only
from one hearphones side.
Transmitter is
in Stereo
mode.
Set the transmitter in Mono mode.
Mode Stereo and MIX activated:
you want to hear only the right
input signal transmitter, even if
the transmitter is in Stereo mode
and both the transmitter inputs
are used. (ING 30 only).
Transmitter is
in Mono mode. Set the transmitter in Stereo mode.
Listening to two independent
mono signals in left and right
earphones, but you want to hear
the signals in both earphones
(ING 30 only).
Activate MIX in the transmitter.
