manualshive.com logo in svg

Advanced Instruments GPR-1200, Owner'S Manual

Share
Download
Advanced Instruments GPR-1200 Owner'S Manual Download Page 9

Advanced Instruments Inc. 

 

by purging with zero or a gas with a low PPM oxygen concentration is recommended after the cleaning process is 

completed.    

 

Mounting:

 The analyzer is approved for indoor as well as outdoor use. However, avoid using the analyzer in an 

area where direct sun might heat up the analyzer beyond the recommended operating temperature range. 

 

Gas Connections:

 The Inlet and outlet vent gas lines require 1/8” or ¼” stainless steel compression type tube 

fittings. The sample inlet tubing must be metallic, preferably SS. The sample vent line may be of SS or hard plastic 

tubing with low gas permeability. 

 

Power:

 The analyzer is powered by an integral lead-acid rechargeable battery. The analyzer will continue to run for 

a minimum of 30-60 days after the battery is fully charged without the pump. If the pump is used, the battery will 

continue to power the pump for up to 8 hours.  

WARRNING: THE ANALYZER BATTERY MUST BE CHARGED IN A SAFE AREA ONLY BY USING FACTORY PROVIDED 

WALL PLUG-IN CHARGER.  

 

8 

 

Summary of Contents for GPR-1200






































Reviews:

No comments

Brands by name

Popular brands

Load more brands