background image

Operation

4-1

General

1.  Power: A circuit breaker switch is located on the lower right rear of the machine to turn power on and

off.

2.  Reset: Located on the right rear enclosure, the reset button is used to start the machine initially and

restart  the  machine  after  an  E-stop  condition  has  occurred.    After  the  power  is  turned  on,  the  reset
button is held for 15 seconds to allow the machines electrical controls to reset to initial settings.

3.  Speed: A potentiometer is used to control the speed that the laminator will run product through.  Your

laminator has the electrical and mechanical capability to run up to 20 feet per minute, but the quality
of the product output is the governing factor in maximum process speed.

4.  E-stops: E-stop switches are located at all four corners to allow the operator to stop the machine and

open  the  nip  rolls  and  pull  rolls  in  case  of  emergency.    The  button  must  be  pulled  back  out  before
pressing the reset button to restart the machine.

5.  Nip  Rolls:    The  nip  rolls  are  the  heart  and  soul  of  the  laminator  and  must  be  cared  for  properly  in

order  to  give  years  of  quality  product  output.    Always  dial  the  shim  wheel  to  a  shim  setting  greater
than  “0”  when  the  machine  is  not  in  use.    This  will  prevent  the  rolls  from  forming  a  flat  spot  from
resting against each other.  This also applies to the pull rolls.

Always  set  the  shim  wheel  to  a  setting  greater  than  “0”  when  the
machine is not in use.  This will prevent the roll from coming together
and forming a flat spot.  Permanent damage can be caused to the rolls

if this warning is not heeded.

6.  Fwd-Rev:  This  button  is  a  lighted  button  that  will  determine  which  direction  the  machine  will  run.    If

the button is  not  lit, the machine  will run from front to back.  If the  button  is  lit,  the  machine  will  run
from back to front.

7.  Stop: This button will stop the rotation of the nip rolls.
8.  Run: This button will allow the machine to run continuously in the direction depicted by the Fwd/Rev

button and at the speed set by the potentiometer.

9.  Foot  Switch:  The  foot  switch  will  run  the  laminator  in  the  direction  depicted  by  the  Fwd/Rev  button

and at the speed set by the potentiometer.  The foot switch is always active, this allows an operator to
press the foot switch to get a print started and then press the Run button to transfer to the continuous
run mode without stopping.

10.  Temperature Control with switch: The two position switch allows the operator to turn the heater in the

roll  on  or  off.    The  temperature  controller  allows  the  operator  to  set  a  desired  temperature  for  a
process.

11.  Brakes:  Turn  the  knob  clockwise  to  increase  web  tension  from  the  unwind  station,  the  LED  display

bars  will  move  up  as  tension  increases.    Turn  the  knob  counter  clockwise  to  decrease  web  tension
from the unwind station, the LED display bars will move down as the tension decreases.

12.  Clutches: Turn the knurled knob towards you to increase the web tension to the windup station.  Turn

the knurled knob away from you to decrease web tension to the windup station.

13.  Pull Roll Clutch:  Turn the regulator clockwise to increase the pressure to the pull roll clutch and pull

roll cylinders and counter clockwise to decrease pressure to the clutch.

Summary of Contents for AGL64i


































































Reviews: