ADTRAN Total Access 1500 FT1 DP Installation And Maintenance Manual Download Page 7

7

Section 61180405L1-5, Issue 1

61180405L1-5A

5. OPERATION

For abbreviations used in the screen diagrams, see

Table 4

.

Table 4.  Definition of Screen Abbreviations

Abbreviation

ES ....................

SES ..................

UAS .................

SF .....................

ESF ..................

B8ZS ................

AMI .................

LBO .................

BPV .................

NIU ..................

S/N ...................

15M .................

24H ..................

Definition

Errored Seconds:  A count of the number of seconds in which at least one code violation was detected on a digital circuit

DS1 (SF)............... Second in which a BPV or frame bit error occurs
DS1 (ESF)............ Second in which a BPV or CRC error occurs
DSL ...................... Second in which a CRC error occurs

Severely Errored Seconds

DS1 (SF)............... Second in which 1554 BPVs or 8 frame bit errors occur
DS1 (ESF)............ Second in which 1544 BPVs or 320 CRC errors occur
DSL ...................... Second in which 165 CRC errors occur

Unavailable Seconds:  A count of the number of seconds that a circuit or path is not available.

DS1 ....................... Second in which there is a loss of signal or frame sync
DSL ...................... Second in which there is a loss of signal or sync

Superframe Format

Extended Superframe Format

Bipolar with 8-Zero Substitution

Alternate Mark Inversion

Line Build Out

Bipolar Violation

DS1 ....................... Second in which a bipolar violation occurs

T1 Network Interface Unit

Serial Number

Fifteen-minute period

Twenty-four-hour period

Summary of Contents for Total Access 1500 FT1 DP



















Reviews: