background image

2

61287843F1-13B

Step 1: Install the 622v ONT

There are two options to install the 622v ONT: Desk Top and Wall 
Mount. Options are described below.

g

     NOTE

Included with the 622v ONT is a 5-foot (1.52 m) power cord. All 
installation locations should be within 5 feet (1.52 m) of a wall 
outlet.

Desk Top Installation

The 622v ONT can be located on a desktop.

f

     

WARNING!

Ensure that the 622v ONT does not come in contact with water or 
other liquids.

f

     

CAUTION!

Ensure that the 622v ONT is not located in direct sunlight or next 
to any thermal obstructions.

Wall Mounting

Refer to 

Figure 3

 when installing the 622v ONT on a wall.

1. Decide on a location for the 622v ONT. Mount below eye-

level so the LEDs are visible.

g

     NOTE

The equipment has been tested and approved according to 
applicable product safety standards that allow mounting heights 
up to 6.6 ft (2 m).

g

     NOTE

Supplied hardware is intended for drywall mounting only. For 
mounting on surfaces other than drywall, obtain the appropriate 
mounting hardware and follow the provided instructions.

Figure 3. Wall Mount Installation

Wall Anchor (2x)

Mounting Screw (2x)

source of 100 - 240 V AC, 50 - 60 Hz. For the United States and 
Canadian applications, an NRTL Listed Limited Power Source 
(LPS) is needed. For deployment in international applications, an 
LPS specifically approved for that country, such as a CE Mark, is 
needed.

Resetting the ONT

A reset button is available if the 622v ONT needs to be rebooted. 
To reset the 622v ONT, press the RESET button for 5 seconds or 
longer.

I

NSTALLATION

After unpacking the unit, inspect it for damage. If damage is 
noted, file a claim with the carrier and then contact ADTRAN. For 
more information, refer to the warranty.

Installation Guidelines

The following are guidelines for basic installation of the 622v 
ONT. Be sure to route and secure the fiber and cables in a 
manner that will prevent damage.

f

     

WARNING!

Read all warnings and cautions before installing or servicing the 
622v ONT.

Installation Overview

To install the 622v ONT, you will need to complete the following 
steps:

“Step 1: Install the 622v ONT”

“Step 2: Connect Fiber”

“Step 3: Connect Customer Interfaces”

“Step 4: Connect Power”

Required Tools:

Be sure to route and secure the fiber and cables in a manner that 
will prevent damage. Standard technician tools and those listed 
below are required for installing the 622v ONT.

Optical power meter with wavelength filtering

Fiberscope or videoscope

#2 Phillips-head screw driver

Drill 

1/4-inch drill bit

Hammer

For fiber optics connections, the following is required:

ODC Fiber Cleaning Tool

Summary of Contents for 622v XGS-PON ONT

Page 1: ...1287843F2 622v XGS PON ONT with EU power adapter included 1287843F3 622v XGS PON ONT with AUS NZ power adapter included 1287843F4 Two POTS RJ 11 Interfaces Remote activation and deactivation Remote firmware upgrades and downgrades Remote OMCI management as per ITU T G 988 Refer to the following table for a description of each feature in Figure 2 Figure 2 ONT Interfaces POWER Power is provided by a...

Page 2: ...ations an NRTL Listed Limited Power Source LPS is needed For deployment in international applications an LPS specifically approved for that country such as a CE Mark is needed Resetting the ONT A reset button is available if the 622v ONT needs to be rebooted To reset the 622v ONT press the RESET button for 5 seconds or longer INSTALLATION After unpacking the unit inspect it for damage If damage is...

Page 3: ...ightning or other electrical events and voids the warranty There are four customer connections on the rear of the 622v ONT 10 Gbps Ethernet RJ 45 Connector 10GE Port 1 Gbps Ethernet RJ 45 Connector GE Port Two voice RJ 11 Connectors POTS 1 and POTS 2 ports To connect the customer interface complete the following For 1 or 10 Gbps Ethernet Connection Refer to Figure 2 and insert a Category 5e or bet...

Page 4: ...load failed Software image flash write failed Software image activation failed Software image commit failed LED Status Indication Optical TX Power 4 0 dBm to 9 0 dBm RSSI max sensitivity 28 0 dBm RX overload 9 0 dBm TX wavelength 1270 nm typical RX wavelength 1577 nm typical Physical Height 1 7 in 4 3 cm Width 6 1 in 15 5 cm Depth 5 3 in 13 4 cm Weight 0 75 lbs 0 3 kg Environmental Operational Tem...

Reviews: