ADTRAN 3G CDMA NIM Configuration Manual Download

Page: 53 / 57

3G CDMA NIM/Cellular Interface

Troubleshooting

61700801G1-29.1H

3. You can then select

Start Debug

and begin receiving debug information for the item you selected.

CLI Troubleshooting

After configuring the 3G CDMA cellular interface and the demand routing interface, several different

debug

commands can be issued from the Enable mode in the CLI to assist in troubleshooting. The

debug

commands send messages when certain types of activity are detected on the interface, and work
hand-in-hand with the

show

commands to verify proper configuration and performance. The

show

commands are described in

Viewing Interface Statistics Using the CLI

on page 47

of this guide. The

debug

commands are detailed in the following table.

Table 6. Cellular and Demand Routing Interface Debug Command Summary

Command

Explanation

debug interface cellular

<slot/port>

diagnostic

[tx | rx | both]

Enables debug events to decode the packets sent between the
3G CDMA NIM module and the cellular modem along the
diagnostic channel.

specifies the debugging of packets sent

from the NIM module to the modem (optional).

specifies the

debugging of packets sent from the modem to the NIM module
(optional).

Both

specifies the debugging of both transmitted and

received packets (optional).

debug interface cellular

<slot/port>

data

Activates debug messages for handshaking signals on the data
channel.

debug interface cellular

<slot/port>

data-hdlc

Activates debug messages for high-level data link control (HDLC)
errors on the data channel.

debug interface cellular

<slot/port>

diag-hdlc

Activates debug messages for HDLC errors on the diagnostic
channel.

debug interface cellular

<slot/port>

download

Activates debug messages for errors regarding application
downloads.

Summary of Contents for 3G CDMA NIM

























































Search results

Summary of Contents for 3G CDMA NIM

Reviews:

Related manuals for 3G CDMA NIM

Brands by name

Popular brands

ADTRAN 3G CDMA NIM, Configuration Manual

Search results

Summary of Contents for 3G CDMA NIM

Reviews:

Related manuals for 3G CDMA NIM

Brands by name

Popular brands