manualshive.com logo in svg

ADTEK AFM-8A, Operation Manual, Page: 2 / 53

Share
Download
ADTEK AFM-8A Operation Manual Download Page 2

II

CopyRight

 ©

  This manual is copyrighted.
  Without the written permission of the Company, any of the paragraphs and chapters of 
this manual shall not be extracted, copied or reproduced and transmitted in any form, or all 
consequences shall be borne by the o

ff

 ender.

  The Company reserves all legal rights.
  The Company reserves the right to make changes to the speci

fi

 cations described in this 

manual without prior notice. Please keep attention to the latest speci

fi

 cations of our o

ffi

  cial 

website.

Safety warning
  Please read this manual carefully before installing, operating or maintaining this 
equipment. Please note the following special signs appearing in this manual or on 
the device, which are used to warn of potential hazards or to interpret and specify the 
operating procedures.

  The presence of such safety signs indicates that there is a danger of 
electricity, and failure to follow certain instructions will result in personal injury.

  This is a safety warning sign that warns of the risk of potential personal injury.
  Please follow all the safety information after this mark to avoid possible injury 
or death.

  The sign for the reminder, to avoid the operation due to inadvertently caused 
the instrument can not work or even damage the instrument or cause harm to 
the person.

  The equipment must be turn o

ff

  all power supplying and grounded before maintenance 

and overhaul.
  Maintenance only work by quali

fi

 ed personnel.

  This manual applies to persons who have been trained to use. The company are not 
responsible for any problems arising out of their abnormal use.

Summary of Contents for AFM-8A






















































Reviews:

No comments