Adtech ACA 140 Instruction Manual Download Page 1

ACA 140-ACA 142 

AC CurrenWoltage Alarms 

Instruction Manual 

1.0  INTRODUCTION 

These instructions refer to the above models. Supplementary 

sheets are attached if the unit has special options or features. 

For  detailed  specifications,  refer  to  the  Data  Bulletin.  All 

AD TECH instruments are factory calibrated and supplied with 

a  label  detailing  the  calibration.  Adjustments  are  normally 

not necessary.  A  simple  check  should  be  performed  to 

verify calibration before installation to ensure that it matches 

the field requirement. 

2.0  GENERAL DESCRIPTION 

The ADTECH ACA 140 and ACA 142 alarms are single and 

dual alarms accepting an AC Current or Voltage input signal 

and providing relay contact output(s). 

The input can be either 0-5 AMPS or an AC voltage of 0-20 V 

to 0-300 Vrange. The instruments can respond either to RMS 

value or  average  value of  the input  signal.  The true RMS 

allows wave forms with 5:1 as crest factor. 

The input frequency range is 25 Hz to 400 Hz.  For the highest 

accuracy calibrate the instrument at  the installed operating 

frequency. 

The ACA 140 is a single alarm providing a DPDT output and 

the ACA  142 is a  dual  alarm  providing 2  SPDT  outputs as 

standard. DPDT output is optionally available and requires the 

'Wide Line"  enclosure. 
The single alarm may be a Hi or Low alarm; the dual alarm may 

be  Hi-Low,  Low-Hi,  Hi-Hi,  or  Low-Low.  Internal  jumpers 

determine the proper relay(s) action. 

The relay coil may be power fail safe (i.e.) energized for normal 

conditions or NON-powerfail safe (i.e.) energizes on abnormal 

conditions. 

Unless otherwise specified, the single alarm is set as Hi trip, 

power fail safe and the dual alarm as Hi-Low trip power fail 

safe. 

LED indicator(s) for alarm condition is provided as standard. 

Green  indicates  normal  condition  and  red  indicates  alarm 

condition. 

3.0  INSTALLATION 

The instrument is supplied in a general purpose enclosure as 

standard. NEMA 4, 7 or 12 and plug in chassis enclosures are 

optionally available. Installation area/location must agree with 

the supplied instruments including operating temperature and 

ambient conditions. 

Electrical Connections 

The 

wire 

used to connect the instrument to the control system 

Input/Output 

should be a twisted pair(s) and sized according 

to normal practice.  Shielded cable is not normally necessary 

(if used, the shield must be grounded atthe ADTE CH instrument 

and left floating at the sensor). 

A 12  position  barrier  terminal  block with  #6-32  screws and 

3/8"  spacing  is  provided  for  1/0  and  power  connection. 

housing ground terminal marked G is also provided. 

Controls 

Internal ZERO and SPAN controls are provided for calibration. 

External mult�urn trip set control(s) is provided to set the trip 

point(s) level on all units. Adjustable dead band and adjustable 

time  delay  control(s)  may  also  be  provided  if  specified.  If 

optional calibrated dial(s) for trip set and/or adjustable dead 

band control(s) is supplied, they are normally mounted in the 

'Wide Line"  enclosure. 

The  external  multiturn  control(s)  is accessible  through  the 

instrument front panel and is clearly marked for ease of use. 

4.0  MAINTENANCE 

These instruments are electronic except for the relay(s) and 

require  no  maintenance  except  for  periodic  cleaning  and 

calibration verification.  Relay output(s) should be verified at 

user established time intervals.  If the unit appears to be mis­

operating it  should be  checked in place per  section  6.0  or 

removed for a bench check per sections 6.0 and 7.0.  MOST 

problems are traced to field wiring and/or associated circuits. 

If the problem appears to be within the instrument, proceed to 

sections 6.0 and 7.0. 

5.0  CONNECTIONS 

Standard connections are shown below and on the instrument 

face plate, Data Bulletin or on attached supplementary sheets. 

ACA 140 

INPUT 

OT05AMPS  { 

CD 

AC ONLY 

CD 

OR 

AC VOLTAGE  { 

CD 

INPUT ONLY 

© 

ACA 140 SINGLE 

ACA 142DUAL 

ACA 142 

INPUT 

CD 

OTO 5AMPS 

AC ONLY 

CD 

OR 

{

CD 

AC VOLTAGE 

INPUT ONLY 

© 

ACA 142 

DPDT OUTPUT 

OPTION O 34 

® 

K1A t 

© 

CD 

© 

Mounting 

K1A L 

=¥ 

Refer  to  the appropriate outline  drawing  for  mounting  and 

© 

© 

CD 

© 

® 

® 

® 

K-1t

-f 

K2A  L

-f 

© 

® 

© 

® 

CD 

K1Bk 

® 

clearance dimensions.  The instrument is surface mounted 

with two #10-32 screws on 8.00 inch centers. 

K1Bt 

N (- FOR DC) 

AC 

L (+ FOR DC) 

r-FP 

-1-

K-2t

-f 

N (- FOR DC) 

AC 

L (+ FOR DC) 

r-FP 

© 

® 

® 

(TB2) 

...r:--

@) 

® 

® 

® 

K2Bk 

® 

(TB2) 

...r:--

® 

190-A-OOOACA-A

Reviews: