ADT Pulse MDC835 Installation Manual Download Page 6 | Manualshive

Page: 6 / 28

ADT Pulse MDC835 Installation Manual Download Page 6

Chapter 1 Introduction

2

Physical Details

Front/Rear Panel

Figure 1: Front/Rear Panel

IR LEDs

They are used to provide illumination for night time. Please

ensure that the two IR LEDs can be revealed in the
transparent Dome.

Light Sensor

This is a hardware sensor to detect lux. Please ensure that

the light sensor can be revealed in the transparent Dome.

Lens

No physical adjustment is required for the lens. Please

ensure that the lens cover remains clean.

LAN port

Use a standard Ethernet cable (not included) to connect
the LAN port of the supplied cable and the Pulse Gateway
or TS Base panel.

Note:

l

Plugging in the Ethernet cable will disable the wireless
interface. Only one interface can be active at any time.

l

The Ethernet cable should only be connected or
disconnected when the camera is powered OFF.
Attaching or detaching the Ethernet cable while the
camera is powered on does NOT switch the interface
between wired and wireless.

«
...
4
5
6
7
8
...
»

Summary of Contents for MDC835





























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands