ADRF PSR-78-9533-UB Manual Download | Manualshive

Page: 49 / 59

background image

Advanced RF Technologies, Inc.

49

7.5.4

System – Update



To perform a firmware update, click on the Update tab and the following screen will appear.

Figure 7-26 System: Update



Click on the Choose File button and locate the firmware file.



Click on the Upgrade button to perform the firmware update.



Once the firmware update is complete, the following popup message will appear:

Figure 7-27 System: Update is Complete Popup Message

7.5.5

System – Backup / Restore

The Backup / Restore section allows the user to save the settings of the repeater. To perform the backup, click
on the Backup button and you will be prompted to save the backup file. To restore the settings to the system,
click on Choose File button, select the backup file, and click the Restore button.

Figure 7-28 System: Backup / Restore

«
...
47
48
49
50
51
...
»

Summary of Contents for PSR-78-9533-UB




























































Reviews:

No comments

Related manuals for PSR-78-9533-UB

Brand: Warwick Pages: 14

Brand: Takstar Pages: 24

Brand: Pyle Pro Pages: 2

Brand: Musway Pages: 36

Two-Rock Jet Signature

Brand: K&M Analog Designs Pages: 7

Stereo Festival II

Brand: Harman Kardon Pages: 16

Brand: Roland Pages: 6

Brand: Cobalt Digital Inc Pages: 20

Brand: Roswell Pages: 20

Brand: Inter-m Pages: 20

Brand: DaytonAudio Pages: 14

Brand: Altinex Pages: 9

Brand: NXP Semiconductors Pages: 9

NUPOWER XTENDER VU4GX01

Brand: NuWaves Pages: 11

elektronik star 10005093

Brand: Chal-tec Pages: 13

LinkNet LNKA100

Brand: Powerwave Technologies Pages: 17

Brand: Fenton Pages: 16

Brand: QSC Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands