ADRF ADXD-LPR User Manual Download | Manualshive

Page: 30 / 56

background image

Advanced RF Technologies, Inc.

30

5.

INSTALLATION

5.1

Pre-Installation Inspection

Please follow these procedures before installing ADXD equipment:

o

Verify the number of packages received against the packing list.

o

Check all packages for external damage; report any external damage to the shipping carrier. If
there is damage, a shipping agent should be present before you unpack and inspect the
contents because damage caused during transit is the responsibility of the shipping agent.

o

Open and check each package against the packing list. If any items are missing, contact ADRF
customer service.

o

If damage is discovered at the time of installation, contact the shipping agent.

o

Verify the AC voltage with DVM (Volt meter) is 110VAC or 220VAC. Incorrect AC voltage can
damage the ADXD HE equipment.

o

This power of this system shall be supplied through wiring installed in a normal building. If
powered directly from the mains distribution system, it shall be used additional protection,
such as overvoltage protection device.

o

Over voltage category(OVC) & Pollution degree(PD)

Over voltage category (OVC) OVC II

Pollution degree (PD)

PD2

5.2

ADXD LPR Installation Procedure

5.2.1

HE Installation Procedure

CAUTION:

ADXD DAS HE should be installed inside building only.

5.2.1.1

Installing a ADXD DAS HE in a rack

The ADXD HE chassis mounts in a standard 19” (483mm) equipment rack. Allow clearance of 3” (76mm) at

the front and rear, and 2” (51mm) on both sides for air circulation. No top or bottom clearance is required.



Consideration:

-

Eight mounting holes are located on 4 corners of ADXD HE to attach it to the 19” rack. The
ADXD HE must be securely attached to a rack that can support the weight of the ADX.



Mount procedure

-

The following steps should be followed while mounting the ADXD HE



Verify that the HE and Mounting holes are in good condition



Set the ADXD DAS HE against the 19”rack and secure the unit with screws



Verify that ADXD HE is securely attached



Connect the GND cable



Connect the RF cable



Connect the Power



Connect the Optic cable

«
...
28
29
30
31
32
...
»

Summary of Contents for ADXD-LPR

























































Reviews:

No comments

Related manuals for ADXD-LPR

Brand: Galleon Pages: 12

Brand: Sea Tel Pages: 107

Brand: camping first Pages: 40

Brand: HiBoost Pages: 15

Brand: Palomar Pages: 2

Brand: Zonet Pages: 2

Brand: Philips Pages: 1

Brand: Philips Pages: 1

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 5

Brand: Philips Pages: 6

Brand: Philips Pages: 7

Brand: Philips Pages: 7

Brand: Philips Pages: 8

Brand: Philips Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands