ADREL ALTIMETER ALT-USB Manual Download Page 4

 

3. Some theory 

 

With the increase in altitude at which it measurement shall be taken the amount column of 

the atmosphere decreases, as well as the pressure measured. Pressure changes with altitude within 
the first  2000m above the sea are fast - with an increase of altitude about 8m atmospheric pressure 
decreases about 1 hPa (see further - bar degree). As a result, measurements made at the same point 
and at the same time at different heights, give different pressure values. In addition the changes in 
pressure at the same point will be affected by the changes in air temperature. 

 

     

4. Drivers installing 

 

Please  install  on  the  PC  the  USB  drivers.  The  drivers  can  be  downloaded  from 

www.adrel.com.pl/download

 - file Altimetr_Program.zip and unzip tem to any folder.  Then copy 

the contents of the folder …/Sterowniki_Builder/ to folder …/windows/system32. They are files : 
<tee35.bpl>  and <vcl35.bpl>. 

 Then  connect  the  altimeter  to  the  computer  via 

adapter  or  cable  with  a  5-pin  tip  (described  above). 
For  the  connection  additional  hubs  can  not  be  used. 
Altimeter  must  be  connected  via  a  USB  cable  AB 
type with plugs directly into the computer. Windows 
automatically  detects  the  connected  device.  On  the 
screen  Found  New  Hardware  Wizard  will  appear. 
Select "Not this time" and press "Next". 

  

Then  select  "Install  from  a  list  or  specific 

location" and press "Next". 
 

Summary of Contents for ALTIMETER ALT-USB










Reviews: