Adp SEP-100 Installation Instructions Manual Download Page 13

 

WARNING

 

 

Electric shock hazard. Can cause injury 

or death. Before attempting to perform 

any service or maintenance, turn the 

electrical power to unit OFF at 

disconnect switch(es). Unit may have 

multiple power supplies.

 

 

WARNING

 

 

Danger of explosion and fire. Can cause 

injury or product or property damage. 

You must follow these instructions 

exactly.

 

 

BEFORE LIGHTING smell all around the appliance 

area for gas. Be sure to smell next to the floor because 

some gas is heavier than air and will settle on the floor.

 

 

Use only your hand to push in or turn the gas control knob.

 

 

Never use tools. If the knob will not push in or turn by 

hand, do not try to repair it, call a qualified service 

technician. Force or attempted repair may result in a 

fire or explosion.

 

 

These unit heaters are equipped with an automatic 

spark ignition system. There is no pilot. In case of a 

safety shutdown, move thermostat switch to 

OFF

, then 

return the thermostat switch to HEAT position.

 

 

GAS VALVE OPERATION FOR HONEYWELL 

VR8205/VR8305 SERIES GAS VALVE (FIG 8)

 

 

  STOP! Read the safety information at the 

beginning of this section.

 

 

 Set thermostat to lowest setting.

 

 

 Turn off all electrical power to appliance.

 

 

  This appliance is equipped with an ignition device 

which automatically lights burners. 

DO NOT 

attempt to light the burners manually.

 

 

  Turn the manual knob on gas valve clockwise to 

OFF

. Do not force.

 

  Wait five minutes to clear out any gas. If you then 

smell gas, 

STOP!

  Immediately call your gas 

supplier from a neighbor’s phone. Follow the gas 

supplier’s instructions. If you do not smell gas, go 

to next step.

 

 

  Turn manual knob on gas valve counterclockwise 

to 

ON

.

 

 

− 

 Turn on all electric power to unit.

 

 

− 

 Set thermostat to desired setting.

 

 

10 

 The combustion air inducer will start. The burners 

will light within 40 seconds.

 

 

11 

 If unit does not light first time (gas line not fully 

purged) it will attempt up to two more ignitions 

before locking out.

 

 

12 

 If lockout occurs, repeat steps 1 through 8.

 

 

13 

 If appliance still will not operate, follow the 

instructions 

“To Turn Off Gas to Unit"

  and call 

your service technician or gas supplier.

 

 

HONEYWELL VR8205/VR8305 SERIES GAS VALVE

 

 

MANIFOLD PRESSURE ADJUSTMENT SCREW

 

 

MANIFOLD

 

PRESSURE

 

TAP

 

 

 

 

 

 
 

 ON

 

 
 

OFF

 

 

INLET

 

PRESSURE

 

     

TAP

 

 

GAS VALVE SHOWN IN OFF POSITION

 

 

FIGURE 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

Electric shock hazard. Can cause 

injury or death. Before attempting to 

perform any service or maintenance, 

turn the electrical power to unit OFF at 

disconnect switch(es). Unit may have 

multiple power supplies.

 

Danger of explosion and fire. Can 

cause injury or product or property 

damage. You must follow these 

instructions exactly. 

13

Summary of Contents for SEP-100





















Reviews: