-２-
00000-1B-10226P4
2) Compressor Level Selector Switch
o HIGH (45dB)
: Select this position when you speak in a low voice or away from the microphone in
a quiet place.(The microphone will pick up the noise around the microphone.)
o LOW (35dB)
: This is optimum position for normal QSO. You can enjoy QSO with enough voice
level at 10cm away from microphone.
o ＭＡＮＵＡL
: Select this position when you operate at noisy area or when you do not want
to use compressor function. The compressor Level Volume③ will be activated.
3) Manual Level Volume : It will be activated when the Compressor Level Selector Switch ② is at
“
Manual
”
position. Adjust it to get an optimum level. (The pointer of level meter
should not deflect over
“
0dB
”
.)
4)
Output Selector
: A changeover switch to select
“
OUT-A
”
⑪ or
“
OUT-B
”
⑫.
5)
“
ON AIR
”
Indicator : Turn the power switch①
“
ON
”
and LED Indicator ⑤ will blink on and off to
indicate the receiving condition.
The LED⑤ will light up continuously when transmitting.
6) PTT Switch
: Use it for short time QSO. While pressing it, the TX LED indicator lights up and
the condition is transmitting. (When press it, it sounds
‘
pip
’
When releasing the
LOCK condition, also press this switch.)
7) ＬＯＣＫ Switch
: Use it for long time QSO. Press it and it sounds
‘
peep
’
.
The LED TX indicator⑤ will light up continuously. The condition is transmitting
until pressing the PTT switch⑥.
8) Level Meter
: You can watch the level of microphone amplifier with this meter. When you use this
microphone with
“
MANUAL
”
position of Compressor Level Selector Switch, you
will have to adjust the indicator of the meter to keep under
“
0dB
”
. Refer to Manual
Level volume③
And it works as battery checker for a few seconds just after switching the power
“
ON
”
.
9)
UP/DOWN Switch
:
The same function as the UP/DOWN switch of transceiver. For details, please read
the instruction book of transceiver.
10) Microphone
:
This model is provided with Electret Condenser type microphone for easy
understanding sound quality.
11) Mic.
Output Connector:
“
OUT-A
”
(8P ADONIS type terminal arrangement)
12) Mic.
Output Connector:
“
OUT-B
”
(8P ADONIS type terminal arrangement)
(Note: The microphone Interconnecting Cables optionally available are provided with
directional condition for connecting. Please connect the cable with
microphone correctly. )
Terminals of Microphone Output Connector and ⑪
&
&
&
&
⑫
and
“
ADONIS
”
standard terminal layout (8P)
(Fig. 2)
* When the transceiver connected to this model is supplying the microphone terminal with
DC5V-9V, 20mA minimum current, this model can get the DC power supply directly from
transceiver by connecting with
“
D
”
series microphone interconnecting cables. For
details, please refer to the list of the microphone interconnecting cables optionally available.
①
②
③
④
⑤
⑥
⑦
⑧
Ｅ：ＭＩＣ.ＥＡＲＴＨ
Ｍ：ＭＩＣ
Ｐ：ＰＲＥＳＳ ＴＯ ＴＡＬＫ
Ｇ：ＰＲＥＳＳ ＴＯ ＴＡＬＫ（ＥＡＲＴＨ）
Ｕ：ＵＰ
Ｄ：ＤＯＷＮ
Ｃ：Ｕ／Ｄ ＣＯＭＭＯＮ
Ｂ：ＤＣ ＦＥＥＤＩＮＧ（ＤＩＲＥＣＴ ＣＵＲＲＥＮＴ）
E
M
P
B
G
U
D
1
2
3
4
5
6
7
8
（ＶＩＥＷＥＤ ＦＲＯＭ ＴＥＲＭＩＮＡＬ ＰＩＮ ＳＩＤＥ）
C
