manualshive.com logo in svg

ADLINK Technology PXI -3950, User Manual, Page: 38 / 85

Share
Download
ADLINK Technology PXI -3950 User Manual Download Page 38

I / O Connectors and Pin Assignments 

 23

PXI -3950

User’s Manual

2.3.2

SATA Port

The PXI-3950 provides a SATA Gen. 1 port and is shipped with 
a pre-installed 2.5" SATA hard drive. The SATA host controller 
supports two modes of operation, the legacy mode using I/O 
space and AHCI mode using memory space. You can also use 
a 2.5" solid state disk (SSD) as a replacement SATA hard drive 
for shock/vibration resistance.

Figure 2-12: SATA Gen. 1 Port & Pin Assignments

Signal 

PIN

PIN

Signal 

GND 1 

2 GND 

Reserve 3 4 Reserve 

Reserve 5 6 Reserve 

Reserve 7 8 Reserve 

Reserve 9 10 

Reserve 

Reserve 11 12 Reserve 

Reserve 13 14 Reserve 

Reserve 15 16 Reserve 

Reserve 17 18 Reserve 

Reserve 19 20  GND 

GND 21 

22 

Reserve 

Reserve 23 24 Reserve 

Reserve 25 26 Reserve 

Reserve 27 28 Reserve 

Reserve 29 30  GND 

Reserve 31 32  +5V 

Reserve 33 34  +5V 

Reserve 35 36  +5V 

Reserve 37 38  +12V 

Reserve 39 40  +12V 

Reserve 41 42  +12V 

GND 43 

44 GND 

SATA_RXn

45 46 SATA_TXn

SATA_RXp

47 48 SATA_TXp

GND 49 

50 GND 

Summary of Contents for PXI -3950






















































































Reviews:

No comments