background image

 Introduction 

IEEE802.3u auto-negotiation support for automatic speed 
selection 
IEEE 802.3X (100base-TX Flow control support) 
Wake on Lan support 
Optional Alert on LAN II support  

z

 

Enhanced IDE:  

Bus Master IDE controller, two EIDE interfaces for up to four 
devices, support PIO Mode 3/4 or Ultra DMA/66 IDE devices, 
including Hard Disk Drive, ATAPI CD-ROM, LS120, and ZIP 
drives. 

z

 

Super I/O Chipset:

  Winbond W83627HF 

z

 

Parallel Port:  

One high-speed parallel port, SPP/EPP/ECP mode 
ESD protection to 4KV 
Downstream device protection to 30V 

z

 

Serial Port: 

One 16550 UART compatible ports with RS-232 interface 
One 16550 UART compatible ports with RS-232/422/485 
ESD protection to 2KV 

z

 

FDD Interface:

 Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB, 

2.88MB) 

z

 

USB Interface:  

Two USB pin-header connectors, compliant with USB 
Specification Rev. 1.1, Individual over-current protection 

z

 

Watchdog Timer:  

Programmable I/O port 2Eh and 2Fh to configure watchdog timer 
Time-out timing select 0~255 seconds or 0~255 minutes 

z

 

Keyboard and Mouse Connectors:  

PS/2 type mini-DIN connectors, and supports a 5-pin internal 
keyboard connector 

z

 

HISA:  

ISA bus high driving capability up to 64mA on all data address and 
control lines 

z

 

Power supply: 

AT/ATX 

z

 

Environmental: 

Storage Temperature

: -20

°

C to 80

°

Operation Temperature

: 0

°

C to 55

°

Humidity

: 5% to 95% 

Summary of Contents for NuPRO-770 Series






































Reviews: