background image

17

 

 

 

aTCA-80606PA 

6.3 Fan Tray Signals 

The Fan Tray provides signals for: 

  Fuse monitoring 

  Status of the Hot Swap Controller 

  Fan Speed 

  Temperature 

These signals are controlled by the IPM Controller devices on the Fan Tray PCB. The Shelf 
Manager has access to these signals via IPMB. 

 

6.4 Fan Tray Indicators 

The front panel includes a green Fan Tray OK LED, a red Fan Tray Fault LED, and a blue 
Hot Swap LED.  

The Hot Swap push button indicates to the Shelf Managers that the Fan Tray is about to 
be removed. Its use is optional, but it is provided so that service personnel can be trained 
to look for a blue LED to be illuminated on any active component before removing it from 
the system. Once the operator pushes the Hot Swap button, the Shelf Manager is 
informed of the pending extraction. When the Shelf Manager feels it is “safe“ to remove 
the Fan Tray, the blue Hot Swap LED illuminates solid. 

 

Table 5: LEDs on Fan Tray front panel 

Color

 

Description

 

Status

 

Condition

 

Green 

Fan Tray OK LED 

Off 

No Power to the Fan Tray 

Solid green 

Normal Operation 

Red 

Fan Tray Fault LED 

Solid red 

Attention Status (error condition) 

Blue 

Hot Swap LED 

Off 

No Power to the Fan Tray, or  
not OK to extract the Fan Tray 

Short blink 

Preparing for extraction 

Solid blue 

Ready to remove 

 
 

 

Summary of Contents for aTCA-80606PA
































Reviews: