ADJ Products, LLC - www.adj.com - Profile Panel RGBA User Manual Page 10
ADJ Products, LLC - www.adj.com - Profile Panel RGBA User Manual Page 9
Profile Panel RGBA Operating Instructions
RGBA Dimmer Mode:
In this mode you can select and adjust the intensity of the red, green,
blue, or amber colors to make your own desired color.
1. Plug the fixture in and press the MODE button until “MANUAL” is
displayed.
2. When “rXXX” is displayed you are in Red dimming mode.
Press the UP and DOWN buttons to adjust intensity. After you
have finished adjusting the intensity, or if you would like to skip to
the next color, press the SET UP button.
3. When “GXXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “bXXX” is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. When “UXXX” is displayed you are in Amber dimming mode.
Press the UP and DOWN buttons to adjust intensity.
6. After you have adjusted the colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the strobe mode.
7. “FSXX” will be displayed, this is strobe mode. The strobe can be
adjusted between “00” (flash off) to “15” (fastest flash).
Auto Run Mode:
In this mode the Profile Panel RGBA will run a auto program.
1. Plug the fixture in and press the MODE button until “AUTO” is dis-
played.
2. After you have activated Auto Run mode, press the SET UP but-
ton to adjust the fade time.
3. When you press SET UP, “FdXX” should be displayed. Use the
UP or DOWN buttons to set the fade speed to either “Fd.00” (fade
off) or between “Fd01” (fastest speed) and “Fd99” (slowest
speed). After adjusting the fade speed, press SET UP if you
wish to activate the Flash mode.
4. “FS.XX” will now be displayed, this is Flash mode. The Flash can
be adjusted between “FS00” (flash off) to “FS15” (fastest flash).
Profile Panel RGBA Operating Instructions
DMX Mode:
There are four DMX Modes to choose from: 4 Channels, 7 Channels,
9 Channels, and 32 Channels. Operating through a DMX controller
give the user the freedom to create their own programs tailored to
their own individual needs.
1. Press the MODE button until “dXXX” is displayed. “XXX” repre-
sents the displayed DMX address. Use the UP and DOWN but-
tons to find your desired DMX address.
2. Once you have found your desired DMX address press the SET
UP button to select you desired DMX channel mode. Use the UP
and DOWN buttons to find you desired channel mode.
• To run the 4 Channel Mode, press the MODE button until “Ch04”
is displayed. This is the 4 Channel Mode.
• To run the 7 Channel Mode, press the MODE button until “Ch07”
is displayed. This is the 7 Channel Mode.
• To run the 9 Channel Mode, press the MODE button until “Ch09”
is displayed. This is the 9 Channel Mode.
• To run the 32 Channel Mode, press the MODE button until “Ch32”
is displayed. This is the 32 Channel Mode.
3. Please see pages 15-20 for DMX values and traits.
4. After you have found your desired DMX mode and set the DMX
address, plug in the fixture via the XLR connections to any stan-
dard DMX controller.
Sound Active Mode:
1. Plug the fixture in and press the MODE button until “SUXX” is
displayed. “XX” represents the sound sensitivity level.
2. Use the UP or DOWN buttons to adjust the sound sensitivity.
“SU00” is off, “SU01 is the lowest sensitivity, and “SU31” is the
highest. After adjusting the sound sensitivity, press SET UP if you
wish to activate the Flash mode.
3. “FS.XX” will now be displayed, this is Flash mode. The Flash can
be adjusted between “FS00” (flash off) to “FS15” (fastest flash).
