ADJ Products, LLC - www.adj.com - Pixel Kling 10C User Manual Page 8
Pixel Kling 10C Operating Instructions
with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“DMX MODE ADDR:XXX” is displayed. “XXX” represents the current
displayed address. Use the UP or DOWN buttons to select your
desired DMX address, then press the SETUP button to select your
DMX Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 5 Channel Mode, press the MODE button until
“CHAN:05” is displayed. This is the 5 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until
“CHAN:007” is displayed. This is the 7 Channel DMX Mode.
• To run the 32 Channel Mode, press the MODE button until
“CHAN:032” is displayed. This is the 32 Channel DMX Mode.
• To run the 480 Channel Mode, press the MODE button until
“CHAN:480” is displayed. This is the 480 Channel DMX Mode.
4. Please see pages 15-22 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode
plug in
the fixture via the XLR connections to any standard DMX controller.
Dimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL” is
displayed. If “MANUAL TUBE: ALL” is displayed then all of the
tubes are being controlled. If “MANUAL TUBE: 01” is displayed,
you are controlling the tube connected to port 1. If “MANUAL
TUBE: 02” is displayed, you are controlling the tube connected to
port 2. If “MANUAL TUBE: 03” is displayed, your controlling the
tube connected to port 3. After deciding what tube(s) to control
press the SET UP button.
2. When “RED: XXX” is displayed you are in Red dimming mode.
Press the UP and DOWN buttons to adjust intensity. After you
have finished adjusting the intensity, or if you would like to skip to
the next color, press the SET UP button.
3. When “GREN: XXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.
4. When “BLUE: XXX” is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired
color you can then activate strobing by pressing the SET UP but-
ADJ Products, LLC - www.adj.com - Pixel Kling 10C User Manual Page 19
Channel 1 will is Master Dimming
When Channel 3 is between the values of 0-41, Channels 5-7 are
used, and Channel 2 will control strobing.
When Channel 3 is between the values of 42-83, Channel 4 is in
Color Macros Mode, and Channel 2 will control strobing.
When Channel 3 is between the values of 84-125, Channel 4 is in
Color Change Mode, and Channel 2 will control the color change
speed.
When Channel 3 is between the values of 126-167, Channel 4 is
in Color Fade Mode, and Channel 2 will control the color fade
speed.
When Channel 3 is between the values of 168-209, Channel 4 is of
no use, and Channel 2 will control the auto run speed.
When Channel 3 is between the values of 210-255, Channel 4 is in
Sound Active Mode, and Channel 2 will control the sound sensi-
tivity.
Channel Value
Function
4 SOUND ACTIVE MODE CONT.
192 - 202 SOUND ACTIVE 19
203 - 212 SOUND ACTIVE 20
213 - 223 SOUND ACTIVE 21
224 - 234 SOUND ACTIVE 22
235 - 244 SOUND ACTIVE 23
245 - 255 SOUND ACTIVE 24
5 RED
0 - 255 0% - 100%
6 GREEN
0 - 255 0% - 100%
7 BLUE
0 - 255 0% - 100%
Pixel Kling 10C 7 Channel - DMX Values & Functions