background image

9

I N S TA L L AT I O N

FLAMMABLE MATERIAL WARNING

Keep fixture minimum 8.5 in. (22cm) away from flammable materials and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualified electrician should be used for all electrical connections and/or installations.

MINIMUM DISTANCE TO OBJECTS/SURFACES IS 1.6 FEET (0.5 METERS).

MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE IS 8.5 IN. 

(22 CM).

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
•  Fixture MUST be installed following all local, national, and country commercial electrical and 

construction codes and regulations.

•  Before rigging/mounting a single fixture or multiple fixtures to any metal truss/structure or placing 

the fixture(s) on any surface, a professional equipment installer MUST be consulted to determine 

if the metal truss/structure or surface is properly certified to safely hold the combined weight of the 

fixture(s), clamps, cables, and accessories.

•  Maximum ambient operating temperature is 104°F (40°C).  Do  not  use  fixture  when  ambient 

temperature exceeds this value.

•  Fixture(s) should be installed outside walking paths, seating areas, or areas where unauthorized 

personnel might reach the fixture by hand.

•  NEVER stand directly below the fixture(s) when rigging, removingm, or servicing.

•  Overhead fixture installation must always be secured with a secondary safety attachment, such as 

an appropriately rated safety cable.

•  Allow approximately 15 minutes for the fixture to cool down before servicing.
IP RATING

This device is IP20 rated. This means that the unit is protected against the intrusion of 

solids 2.5mm in size or larger (approximately the size of an adult finger tip). The unit is NOT 

protected against water or liquid intrusion of any kind!
RIGGING

Overhead rigging requires extensive experience, including calculating working load limits, 

knowledge of installation material being used, and periodic safety inspection of all installation 

material and the fixture, among other skills. If you lack these qualifications, do not attempt the 

installation yourself. Improper installation can result in bodily injury.

Summary of Contents for Jolt Bar FX

































Reviews: