ADJ ILLUSION DOTZ 3.3 User Instructions Download Page 24

ADJ Products, LLC  -  www.adj.com  - Illusion Dotz 3.3 Instruction Manual Page 46

  Illusion Dotz 3.3   

 

                             Warranty

MANUFACTURER’S LIMITED WARRANTY

A.  ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products

 

to be free of manufacturing defects in material and workmanship for a prescribed period from 

 

the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the 

 

product is purchased within the United States of America, including possessions and 

 

territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable

 

evidence, at the time service is sought. 

B.   For warranty service you must obtain a Return Authorization number (RA#) 

 

before sending back the product–please contact ADJ Products, LLC Service Department 

 

at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All 

 

shipping charges must be pre-paid. If the requested repairs or service (including 

 

parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return 

 

shipping charges only to a designated point within the United States. If the entire instrument is 

 

sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If 

 

any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for 

 

loss of or damage to any such accessories, nor for the safe return thereof.  

C.   This warranty is void if the serial number has been altered or removed; if the product is modified in any 

 

manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the 

 

product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior 

 

written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because 

 

not properly maintained as set forth in the instruction manual. 

D.  This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check 

 

up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense 

 

with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by 

 

reason of defects in material or workmanship.  The sole responsibility of ADJ Products, LLC under this 

 

warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole 

 

discretion of ADJ Products, LLC.  All products covered by this warranty were manufactured after August 

 

15, 2012, and bear indentifying marks to that effect.

E.  ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products 

 

without any obligation to include these changes in any products theretofore manufactured. 

 

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with 

 

products described above. Except to the extent prohibited by applicable law, all implied warranties made 

 

by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, 

 

are limited in duration to the warranty period set forth above. And no warranties, whether expressed or 

 

implied, including warranties of merchantability or fitness, shall apply to this product after said period 

 

has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is 

 

expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or 

 

damage, direct or consequential, arising out of the use of, or inability to use, this product. 

 

This warranty is the only written warranty applicable to ADJ Products, LLC Products and 

 

supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore 

 published. 

MANUFACTURER’S LIMITED WARRANTY PERIODS:
 

• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent 

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par  Cans, Trussing, 

Lighting Stands etc. excluding LED and lamps) 

 

• Laser Products = 90-Day Limited Warranty

 

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power 

 

   supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day 

 

   limited warranty).

Model:    

 

Illusion Dotz 3.3

Voltage:     100~240V, 50/60Hz

LEDs:   

 

 

9 x 30W RGB COB LEDs

Beam Angle:   

 

15 Degrees

Power Consumption: 

285W

Power Cord Daisy Chain:  4 Fixtures Max. (120V)

 

 

 

 

9 Fixtures Max. (220V)

Dimensions:    15”(L) x 10.5”(W) x 20.25”(H)

 

 

 

 

380mm x 264mm x 512mm

Weight: 

 

 

29 Lbs. / 13 kgs.

Fuse:   

 

 

4A

Duty Cycle:   

 

None

DMX:   

 

 

3 DMX Channel Modes: 12 Channels,  

 

 

 

 

14 Channels, or 38 Channels

Sound Active: 

 

Yes

Working  Position:   

Any Safe, Secure Position

Warranty: 

 

 

2 Year (730 days)

Please Note:

 Specifications and improvements in the design 

of this unit and this manual are subject to change without any 

prior written notice.

  Illusion Dotz 3.3                                           Specifications

Auto  Sensing  Voltage:

  This  fixture  contains  an  electronic 

voltage switch, which will auto sense the voltage when it is 

plugged into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Summary of Contents for ILLUSION DOTZ 3.3

























Reviews: