©
American DJ Supply
®
- www.americandj.com - Gobo Projector LED™ User Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Gobo Projector LED™ User Manual Page 3
Gobo Projector LED™
Precautions
Safety Issue:
This unit may blow the fuse if the maximum allotted
load of 2 amps is reached. If the fuse needs replacement, please see
fuse replacement on page 5.
• Be sure the local power outlet match the required voltage of the
unit.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture. Do not attempt to remove or break off the ground prong
from the electrical cord. This prong is used to reduce the risk of
electrical shock and fire in case of an internal short.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
Gobo Projector LED™
Operation
Introduction:
The American DJ
®
Gobo Projector LED
™
is a rotating
gobo projector. This fixture is designed for mobile DJ’s, clubs, bands,
roller rinks and any arena that requires a compact, light weight, easy
to use unit.
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
®
Gobo Projector LED™ before attempting operation.
Operation:
This fixture is designed to operate as a stand alone,
rotating gobo projector, there is no need of a controller. It has been
tested and there is no assembly necessary. The Gobo Projector
LED™ is ready to be plugged in out of the box. Only use the included
I.E.C. power cable supplied with the unit. When this fixture is plugged
in, the unit will project the included gobo. Using the switch located at
the back of the unit, you can make the gobo remain static or make
the gobo rotate counter-clockwise.
After plugging the unit if there is no LED output check the fuse. If the
fuse has not popped, please contact customer support for further
instructions. This fixture features a light weight case design and an
adjustable hanging bracket.
Gobo Projector LED™
Warranty Registration
The Gobo Projector LED™ carries a three year (1095 days) limited
warranty. Please fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a return authorization (R.A.)
number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact American DJ
®
customer
support for a R.A. number.
The Gobo Projector LED™ comes with a replaceable gobo. This
gobo can be interchanged at any time and allows you to customize
your system.
To replace gobo;
1. Unscrew the two screws located at the top that hold the gobo
housing.
2. Remove the gobo housing.
3. Once the gobo housing has been removed, remove the retaining
ring that holds the gobo in. This can easily be done using needle
nose pliers.
4. Remove and replace the gobo with your desired replacement.
Reinsert the retainer ring, and make sure the ring rests firmly
against the gobo.
5. Slide the gobo assembly back into place, and secure the housing
with two screws.
Gobo Projector LED™
Gobo Replacement
