background image

 Galaxian Gem IR    

 

                             Warranty

MANUFACTURER’S LIMITED WARRANTY

A.  ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products

 

to be free of manufacturing defects in material and workmanship for a prescribed period from 

 

the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the 

 

product is purchased within the United States of America, including possessions and 

 

territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable

 

evidence, at the time service is sought. 

B.   For warranty service you must obtain a Return Authorization number (RA#) 

 

before sending back the product–please contact ADJ Products, LLC Service Department 

 

at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All 

 

shipping charges must be pre-paid. If the requested repairs or service (including 

 

parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return 

 

shipping charges only to a designated point within the United States. If the entire instrument is 

 

sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If 

 

any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for 

 

loss of or damage to any such accessories, nor for the safe return thereof.  

C.   This warranty is void if the serial number has been altered or removed; if the product is modified in any 

 

manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the 

 

product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior 

 

written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because 

 

not properly maintained as set forth in the instruction manual. 

D.  This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check 

 

up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense 

 

with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by 

 

reason of defects in material or workmanship.  The sole responsibility of ADJ Products, LLC under this 

 

warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole 

 

discretion of ADJ Products, LLC.  All products covered by this warranty were manufactured after August 

 

15, 2012, and bear indentifying marks to that effect.

E.  ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products 

 

without any obligation to include these changes in any products theretofore manufactured. 

 

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with 

 

products described above. Except to the extent prohibited by applicable law, all implied warranties made 

 

by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, 

 

are limited in duration to the warranty period set forth above. And no warranties, whether expressed or 

 

implied, including warranties of merchantability or fitness, shall apply to this product after said period 

 

has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is 

 

expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or 

 

damage, direct or consequential, arising out of the use of, or inability to use, this product. 

 

This warranty is the only written warranty applicable to ADJ Products, LLC Products and 

 

supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore 

 published. 

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 

• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent 

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par  Cans, Trussing, 

Lighting Stands etc. excluding LED and lamps) 

 

• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month 

limited warranty)

 

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power 

 

   supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 1 Year 

Limited Warranty) Note: 2 Year Warranty only applies to purchases within the United States.

 

• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty (excluding faders and tact switches)

Fixture Cleaning:

 Due to fog residue, smoke, and dust cleaning 

the internal and external lenses should be carried out periodically to 

optimize light output.  

1.   Use normal glass cleaner and a soft cloth to wipe down the out- 

  side casing.

2.   Clean the external optics with glass cleaner and a soft cloth every  

  20 days.

3.   Always be sure to dry all parts completely before plugging the  

  unit back in.

Cleaning frequency depends on the environment in which the fixture 

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-

mend cleaning on a monthly basis. Periodic cleaning will ensure lon-

gevity, and crisp beam output.

  Galaxian Gem IR   

 

                              Cleaning

  Galaxian Gem IR   

 

                 Trouble Shooting

Trouble Shooting: Listed below are a few common problems that 

you may encounter, with solutions.
No light output from the unit;
1.  

Be sure the external fuse has not blown. The fuse is located on  

   the rear panel of the unit. 

2.   Be sure the fuse holder is completely and properly seated. 

 

Unit does not respond to sound;
1.     Low frequencies (bass) should cause the unit to react to sound.

    Tapping on the microphone, quiet or high pitched sounds may

   not activate the unit.  

  Galaxian Gem IR                                             Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been 

removed, the fuse holder is located above the I.E.C. power cord input. 

Using a phillips head screw driver unscrew and remove the fuse holder. 

Remove the bad fuse and replace with a new one. Reinsert the fuse 

holder and tighten with the screwdriver.

ADJ Products, LLC  -  www.adj.com - Galaxian Gem IR Instruction Manual Page 21

ADJ Products, LLC  -  www.adj.com - Galaxian Gem IR Instruction Manual Page 20

Summary of Contents for GALAXIAN GEM IR













Reviews: