manualshive.com logo in svg

ADJ FOCUS SPOT 2X, User Instructions, Page: 25 / 30

Share
Download
ADJ FOCUS SPOT 2X User Instructions Download Page 25

ADJ Products, LLC  -  www.adj.com  - Focus Spot 2X User Manual Page 24

  

Focus Spot 2X

                                                                             

Gobo Replacement

The gobo’s featured in this unit are interchangable. Remember when changing these gobo’s that 

they are thin and easy to bend. Please do this process gently so you do not bend or damage gobo.

Caution! Never open the unit when in use. Always disconnect the main power before attempting to 

change the gobos. 
Locating the Gobo wheel: After disconnecting the main power, position the head with the lens 

facing forward. Look through lens of the unit. When looking through the front lens, position the head 

so that the gears are on the right side. When the gears are on the right side, the shell that needs to 

be uscrewed is now facing up. 
1. To change a gobo, rotate the moving head so that the UV  lens is located on top. Unscrew the  

     

    single middle screw. See instruction number 1 on the next page. 
2. Once you loosen the single screw you are able to swing the head back. See instruction number    

    2 on the next page. You will now be able to access the gobo wheel. Turn the wheel with your  

 

    hand until you come across the gobo you would like to change.
3. To remove the gobo holder gently pull the gobo holder towards the front of the unit and slide it up     

    and out.
4. Gently and carefully remove the retainer ring. After the retainer ring is removed, carefully remove      

    the gobo.

  

5. Change the gobo and replace the retainer ring. Carefully slide the gobo holder back into the housing  

    slot. 
6. Reassemble the unit.

  

Focus Spot 2X

                                                                                                      

Gobos

GOBO 1

GOBO 2

GOBO 3

GOBO 4

GOBO 5

GOBO 6

Inner Diameter: 23.8mm

Outer Diameter: 19mm

Thickness: 0.2mm

Summary of Contents for FOCUS SPOT 2X































Reviews:

No comments