GB
GB
13
tion, the switching on of the signal lamp (20) for the
signalling of the full recovery tank and consequently
to the drying stop.
When this happens, it is necessary to empty the re-
covery tank (see under paragraph “RECOVERY TANK
EMPTYING AND CLEANING”).
STOP OF THE MACHINE AFTER
CLEANING OPERATION
IN AUTOMATIC OR MANUAL WORKING MODE:
1. A the end of the washing cycle put the selector
(12) into the central position (BREAK WASHING). In
this way automatically the brushes lift, the solenoid
valve shuts down and it is possible to finish the dry-
ing operation.
2. When the accelerator pedal is released for more
than 3 seconds, the squeegee raises itself and the
suction switches off automatically.
3. After three seconds, the accelerator can be
pressed again, if a machine's transfer has to be made
(the transfer can be carried out also if the pedal is
never lifted, in this case the squeegee gets lifted and
the suction stop automatically after 15 seconds).
4. Turn the switch key counterclockwise to switch
off the machine.
5. Insert the parking brake (see under paragraph
“EMERGENCY-PARKING BRAKE”).
ATTENTION:
The mode (BREAK WASHING) is specific for the
transfer at the end of the cleaning operation.
Starting again the cleaning operation:
A. by positioning to the left the selector (12) into
position (AUTO) one can start again to work in an
automatic mode.
B. by positioning to the right the selector (12) into
position (MAN) the machine re-establishes the func-
tions pre-set manually.
DAILY MAINTENANCE
ATTENTION:
All the maintenance and cleaning operations that
refer to the following components that are in con-
tact with liquids and therefore:
•
solution and recovery tanks
•
collection box
•
solution and recovery filters
•
squeegee with their rubbers and hoses
•
brushes
must be carried out using gloves to protect from
contact with dangerous solutions
.
RECOVERY TANK EMPTYING AND CLEANING
1. Hold the exhaust hose (1) placed in the rear part
of the machine after having taken it off from its fix-
ing support.
2. Take off the plug (2) from the exhaust hose act-
ing upon its lever (3) and empty the recovery tank
into appropriate containers, in compliance with the
respective rules what the liquid disposal concerns.
3. Unscrew and take off the upper inspection cap
(4).
4. Rinse the inside of the tank with a water jet
through the inspection hole paying attention to
clean also the protection of the float switch placed
right under the hole.
5. In case there should be solid waste or encrusta-
tion on the bottom of the tank, it is possible to use
the lower cleaning door (6). To open it, it is necessary
to act upon the lever (7) to release the closing
bracket (8).
6. Reassemble all parts.
ATTENTION:
Do not open the lower cleaning door if the recovery
tank contains water, check through the upper in-
spection cap that it is empty.
EMPTYING AND CLEANING OF THE COLLECTION
BOX
The machine is equipped with a collection box for
the solid dirt.
At the end of the cleaning operation it is necessary
to empty and to clean it with a water jet.
For the emptying and the cleaning of the box it is
convenient to bring the brushes base in working po-
sition, then:
1. Position the selector (4) for the adjustment of
the brushes pressure on position P1.
2. Activate the machine (see under paragraph
“STARTING OF THE MACHINE”) positioning the selec-
tor (12) to the right to choose the manual mode
(MAN).
3. Activate the selector (14) of up/down of the
brushes base to lower the brushes.
4. Turn the key counterclockwise to turn off the
machine.
ATTENTION:
To carry out above operations with the electric sup-
ply on, may cause damages to hands.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.
5. Open the bar of the right side rubber after hav-
ing released it pulling the stop (1) upwards (1).
