Adeunis RF 7016A-ARF8133 User Manual Download Page 4

 

Page 

4

 / 

28

 

 

DISCLAIMER 

This document and the use of any information contained therein, is subject to the acceptance of the Adeunis RF 
terms and conditions. They can be downloaded from

 www.adeunis.com.

 

Adeunis makes no warranties based on the accuracy or completeness of the contents of this document 
and reserves the right to make changes to specifications and product descriptions at any time without 
notice. 

Adeunis reserves all rights to this document and the information contained herein. 
Reproduction use or disclosure to third parties without express permission is strictly 
prohibited. Copyright © 2016, Adeunis. Adeunis is a registered trademark in the EU and 
other countries. 

All rights to this manual are the exclusive property of ADEUNIS All rights reserved. Copying this manual (without 
written permission from the owner) via printing, copying, recording or by any other means, translating this manual 
(in full or partially) into any other language, including all programming languages, using any electrical, mechanical, 
magnetic or optical devices, manually or any by other methods, is prohibited. 

ADEUNIS  reserves the right to change the technical specifications or functions of its products, or to cease 
manufacturing any of its products, or to cease technical support for one of its products without notice in writing 
and urges its customers to make sure that the information they have is valid. 

ADEUNISF configuration software and programs are available free of charge in a non-modifiable version. 
ADEUNISF can make no guarantees, including guarantees concerning suitability and applicability for a certain 
type of application. Under no circumstances can the manufacturer, or the distributor of an ADEUNIS RF program, 
be held liable for any damage caused by the use of the aforesaid program. Program names, as well as all 
copyright relating to programs, are the exclusive property of ADEUNIS. Any transfer, granting of licenses to a third 
party, leasing, hire, transport, copying, editing, translation, modification into another programming language or 

reverse engineering are prohibited without ADEUNIS’s prior written authori

zation and consent. 

ADEUNIS  
283, rue Louis Néel 
38920 Crolles France 

Tel33 (0)4 76 92 07 77  

Fax +33 (0)4 76 04 80 87 

 

 

Summary of Contents for 7016A-ARF8133





























Reviews: