background image

Page 5

Manual SVA alarm dialler | Back to 

Index

Adesys B.V. | Wateringen

2.  Connection

To connect the SVA correctly, we recommend using exclusively Camden CTB922HE/# type connectors.

Measurements may be affected if other connectors are used.

2.1.  Positioning

Position the SVA where it is not affected by direct sunlight or other heat sources. Choose the place of 

installation such that moisture cannot penetrate the device. The SVA can be mounted onto the TS35 rail 

without screws. The permitted ambient temperature range for the electronics is -20°C to +50°C.

The transmission power of the SVA’s internal GSM/4G module is higher than that of a standard mobile 

phone. Under certain conditions this may affect the functioning of surrounding electronic equipment. The 

effects depend upon the distance between the antenna and surrounding equipment.

2.2. 

Affixing and removal: DIN rail

The SVA should be affixed to a DIN rail before connection.

  

• 

Put the SVA onto the DIN rail at an angle [1]. It is important that the SVA’s DIN rail clip is positioned on 

the top of the DIN rail.

  

• 

Tilt the SVA to clip it into place [2]. Then check whether it is securely seated.

The SVA is removed from a DIN rail as follows.

  

• 

Place a screwdriver on the underside of the DIN rail clip [3]. Use this as a lever; after approx. 3 mm the 

SVA can be tilted to release it from the DIN rail.

2.3. 

SIM card

The size of the SIM card is the mini SIM card size. If the SIM card has a PIN code, this should be entered in 

the setup tool SV-prog. The required SIM card is installed as follows:

• 

Switch the SVA off by disconnecting the supply voltage, then press and hold the reset key for 8 seconds 

to switch off the dialler;

• 

The SIM card holder is made accessible by pressing the button next to it using a sharp object. The 

holder is then pushed outwards;

•  Place the SIM card in the holder and slide this back into the SVA;

•  Reconnect the supply voltage to switch the SVA on.

The SVA should be completely switched off before the SIM card is installed. Fitting or removing the SIM 

card with the SVA switched on may damage the SIM card.

Summary of Contents for SVA














Reviews: