ADENDORFF MAC-AFRIC COMPRE-024 Original Operating Instructions Download Page 12

AIR COMPRESSORS

DIRECT & BELT DRIVEN MANUALS

COPYRIGHT ADENDORFF MACHINERY MART

12

PETROL COMPRESSORS 

ENGINE MANUAL

Illustrative purposes only

Illustrative purposes only

2

11

7

6

5

10

4

3

1

12 13

14

9

15 16

17 18

19

8

GENERAL ARRANGEMENT (PETROL MODEL)

I.      Inspection Plug 

 

8.    On/Off Switch  

14.    Pressure Gauge 

2.  Air Receiver   

 

9.    Solenoid Valve 

15.    Non-return Valve

3.  Oil Filler/Breather 

 

10.  Wire Guard   

& Automatic Pressure Controller

4.  Exhaust (Motor) 

 

11.  Air Delivery Pipe 

16.    Safety Valve

5.  Air Filter (Motor) 

 

12.  Air Compressor Pump  17.    Oil Level Sight Glass  

6.  Petrol Motor  

 

13.  Air Intake Filter 

18.    Oil Drain Plug

7.  Pull Start Recoil 

 

 

 

 

19.    Drain Tap   

 

 

 

 

       

Note: Illustrations are for reference only. Certain models may differ.

Periodic maintenance and adjustment is necessary to keep the compressor engine in good operating 
condition. Perform the service and inspection at the intervals shown in the Maintenance Schedule on 
page 13:

KEY

1. 

Service more frequently when used in dusty areas.

2. 

These items should be serviced by an authorised compressor dealer.

3. 

For professional use, log hours of operation to determine proper 

 

maintenance intervals.

Figure 6

Summary of Contents for MAC-AFRIC COMPRE-024




















Reviews: