ADEMCO Vista-128B PLUS, Installation And Setup Manual

Page: 45 / 138

Section 3 - Installing the Control
3-25
}
ECHELON NETWORK
(PASSPOINT ACS)
YELLOW
RED
BLACK
PROM C
TRANSFORMER
4-PIN
KEYPAD
PLUG
}
TO
CONTROL’S
KEYPAD
TERMINALS
GREEN
Figure 3-32: Wiring the VISTA Gateway Module
Event Log Connections
This system has the ability to record up to 512 events of
various categories in the Event Log (history log). Each
event is recorded with the time and date of its
occurrence (if real-time clock is set). These categories
are Alarm, Supervisory/Check, Bypass, Open/Close, and
System conditions. The log may be viewed on an alpha
keypad, or printed on a parallel or serial printer.
NOTE: If you are using a parallel printer you must use
the VA8201 Alpha Pager Module.
Printer Configurations
Configure the serial printer as follows:
•
7 data bits, even parity, 1 stop bit
•
1200 baud
•
When using a printer, field 14 must be
programmed for RS232 input (1). Zone 9
can longer be used as a protection zone.
•
If you are using a serial printer, terminal 23
on the control panel cannot be used to
interface with Automation software
.
Using the Alpha Pager Module (APM)
To connect a printer using the Alpha Pager Module,
perform the following steps:
Step Action
1 Connect the APM to the control (see
Installing the Alpha Pager Module
previously in this section).
2 Connect the printer according to the
instructions that accompany the APM.
Using the 4100SM
To connect a serial printer using the 4100SM, refer to
Figure 3-33 and perform the following steps:
Step Action
1 Connect terminal 23 on the control panel to
terminal 3 on the 4100SM.
Step Action
2 Connect terminal 6 on the 4100SM to the
Brown wire on the 4142TR cable.
3 Connect the 4142TR cable to J8 on the
control.
4 Connect terminals 8 and 7 of the 4100SM to
terminals 6 and 7 (aux. power (+) and (-)),
respectively of the control.
5 Connect the UL EDP Listed serial printer to
the 4100SM Interface Module.
NOTES:
The 4100SM Module is supplied with a 10-
foot RS232 cable. A longer cable can be used
if the VISTA-128B PLUS is separated from
the serial printer by more than 10 feet, but
the total cable length should be less than 50
feet.
See the 4100SM Installation Instructions for
details concerning the serial printer
operation.
23 1 2 3 4 5 6 7 8 9
NU
CONTROL
PANEL
J8 CONNECTOR
VIOLET GREY
YELLO
W
RED GREEN
BR
O
W
N
BLUE BLA
C
K
IN 2 IN 3
GR
OUND
OUT 5 OUT 6
GR
OUND
GR
OUND
PR
IN
TER
D
TR
4142TR CABLE (SUPPLIED WITH 4100SM)
8
7
6
5
4
3
2
1
4100SM SERIAL MODULE
+ PWR
- (GND)
RXD
not used
not used
TXD
not used
DTR
BLUE WHITE
To TB6 Aux. Power (+)
(25mA current draw)
To TB7 Aux. Power (-)
USE GENDER CHANGER
SUPPLIED WITH 4100SM
IF PRINTER HAS DB25
MALE CONNECTOR
3M
Cable
Supplied with
4100SM
SERIAL PRINTER
SET FOR: 8 DATA BITS
EVEN PARITY
STOP BIT
300/1200 BAUD
4100SM JUMPERS
(CUT TO SET RESPECTIVE SIGNAL FLOATING)
COLOR FUNCTION PIN #
RED
BLUE
WHITE
CD
CTS
DSR
8
5
6
RED
4100SM-010-V0
Figure 3-33: Printer Connections to the 4100SM