Addi-Data APCI-1032 Technical Description Download

Page: 15 / 67

APCI-1032, APCI-1564 and APCI-2032

Technical data

WARNING!

The supply lines must be installed safely against mechanical
loads.

4.3

Versions

The boards are available in the following versions:

APCI-1032: 32 digital inputs

APCI-1032

APCI-1032-12

APCI-1032-5

Input voltage

24 V

12 V on request 5 V on request

APCI-2032: 32 digital outputs

APCI-2032

APCI-2032-5

Output voltage

24 V

5 V on request

APCI-1564: 32 digital inputs and 32 digital outputs

WARNING for the APCI-1564!

When all inputs are connected, the temperature of the printed
circuit card increases.

Make sure that the maximum supply voltage of 26 V is not exceeded

. Please

consider the given Limit values. (See below)

APCI-1564

APCI-1564-5

Input voltage

24 V

5 V on request

Output voltage

24 V

5 V on request

4.4

Limit values

Max. altitude: ............................................ 2000 m
Operating temperature: ............................. 0 to 60

Storage temperature: ................................. -25 to 70

Relative humidity at indoor installation

50% at +40 °C
80% at +31 °C

Minimum PC requirements:
PCI BIOS from Version 1.0

Summary of Contents for APCI-1032




































































Search results

Summary of Contents for APCI-1032

Reviews:

Related manuals for APCI-1032

Brands by name

Popular brands

Addi-Data APCI-1032, Technical Description

Search results

Summary of Contents for APCI-1032

Reviews:

Related manuals for APCI-1032

Brands by name

Popular brands