ADC Ultra-8 Operator'S Manual Download Page 12

Page: 12 / 15

Page 11

Advanced Digital Controls

AS208-OM-V1.1

MENU 4

MENU 4 -- BUZZER PITCH

BUZZER PITCH

This command allows you to change the pitch of the buzzer on the keypad from a high
pitch to a low pitch or switch the buzzer off. E.g. bedroom situations.

Number

Pitch

Highest Pitch

2
3
4
5

Medium Pitch

6
7
8
9

Lowest Pitch

Buzzer Off

e.g. Press MENU + 4 + 5 + ENTER. This set the buzzer pitch to medium pitch.

MENU 5

MENU 5 –– DAY ALARM ON/OFF

DAY ALARM ON/OFF

The Day Alarm is a zone that can be used to operate a buzzer or light to let you know that
you have a visitor when the alarm is disarmed.

Press MENU + 5 to switch the Day Alarm ON/OFF

The buzzer will beep 3 times to let you know that you have switched the Day Alarm ON

The

STAY

button will flash indicating that Day Alarm is ON

When the system is armed it changes to become a full alarm zone. Ask your installer for more information.

www.msealarms.com.au

Summary of Contents for Ultra-8
















Search results

Summary of Contents for Ultra-8

Reviews:

Related manuals for Ultra-8

Brands by name

Popular brands

ADC Ultra-8, Operator'S Manual

Search results

Summary of Contents for Ultra-8

Reviews:

Related manuals for Ultra-8

Brands by name

Popular brands