ADC Modem MM701G User Manual Download Page 68 | Manualshive

Page: 68 / 108

background image

Viewing System Information

62

MM701G User Manual

V

IEWING

S

YSTEM

I

NFORMATION

The System Information page is a read-only summary of the current modem configuration. It
includes information about the firmware release, model, release date, MAC address, and DSP
version. This information is often used by technical support when troubleshooting.

1

From the

Main Menu

, select

System Information

to access the

System Information

page.

2

View the information.

System Information

1. Firmware Release

1.4.1

2. Model

MM701G

3. Release date

May 24 2001

4. MAC address

00:20:A7:A2:01:C0

5. DSP version

R1.2 -5

Press any key (Return to exit) ->

«
...
66
67
68
69
70
...
»

Summary of Contents for Modem MM701G













































































































Reviews:

No comments

Related manuals for Modem MM701G

Brand: Z-Wave.Me Pages: 4

Nighthawk C7000

Brand: NETGEAR Pages: 18

Brand: Encore Networks Pages: 6

Brand: Nokia Pages: 10

Brand: TP-Link Pages: 47

OfficeConnect 3C891A

Brand: 3Com Pages: 24

Brand: Fritz! Pages: 2

Brand: Access Pages: 126

Brand: Ewave Pages: 20

Brand: Raymar Pages: 19

ARRIS SURFboard SBV2402

Brand: CommScope Pages: 40

Brand: HORNER Pages: 11

U.S. Robotics 56K Winmodem

Brand: 3Com Pages: 58

Brand: Campbell Pages: 28

Brand: Uconnect Pages: 8

Brand: Campbell Pages: 48

Dr. Neuhaus Tainy GMOD-T1

Brand: Sagem Pages: 31

Brand: Multitech Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands