background image

Product Support

 

350-200-115-02, Issue 2

18

September 25, 1998

 HLU-200 List 1E

P

RODUCT

 S

UPPORT

ADC Customer Service Group provides expert pre-sales and post-sales 
support and training for all its products.

Technical support is available 24 hours a day, 7 days a week by contacting 
the ADC Technical Assistance Center (TAC).

Sales Assistance

800.366.3891 extension 73000

(USA and Canada)

952.917.3000

Fax: 952.917.3237

Quotation Proposals

Ordering and Delivery

General Product Information

Systems Integration

800.366.3891, extension 73000 
(USA and Canada)

952.917.3000

Complete Solutions (from concept to 
installation)

Network Design and Integration Testing

System Turn-Up and Testing

Network Monitoring (upstream or downstream)

Power Monitoring and Remote Surveillance

Service/Maintenance Agreements

Systems Operation

ADC Technical Assistance Center

800.638.0031

714.730.3222

Fax: 714.730.2400

Email: [email protected]

Technical Information

System/Network Configuration

Product Specification and Application

Training (product-specific)

Installation and Operation Assistance

Troubleshooting and Repair/Field Assistance

Online Technical Support

www.adc.com/Knowledge_Base/index.jsp

Online Technical Publications

www.adc.com/library1/

Product Return Department

800.366.3891 ext. 73748 or

952.917.3748 

Fax: 952.917.3237

Email: repair&[email protected]

ADC Return Material Authorization (RMA) 
number and instructions must be obtained 
before returning products.

All 800 lines are toll-free in the USA and Canada.

Summary of Contents for HiGain HLU-200



























Reviews: