manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Share
Download
ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 50

6.4.12 Resetting the Fail-open Converter

Parts

•

Fuse resistor spare part kit: 6132.00.250 (20pcs)

Info

•

Converter with 1 connector have 2 fuse resistors

Resetting / replacing the fuse resistors

1. Disconnect and disassemble the light fixture.
2. Locate the fuse resistors.

Note

Refer to 

Figure 23

 figure.

Figure 23: Converter with 1 connector

3. Remove the fuse resistors by pulling away from the converter: For converters with 1 connector, always replace both fuse

resistors at the same time.

4. Dispose the old fuse resistor.
5. Place the legs of the new fuse resistors in the sockets.
6. Assemble the light fixture and perform a functional test.

6.4.13 Checking the Light Fixture for Water-tightness

To test for leaks, perform the following procedure for at least 3 minutes:

1. Refer to 

Figure 24

 figure.

Remove pressure relief screw.

2. Refer to 

Figure 25

 figure.

Screw pressure test fitting into the pressure relief port (the opening created when the pressure relief screw is removed).

Screw fitting hand-tight.

RELIANCE Omni 1-Dome,
Maintenance

40
Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Summary of Contents for RELIANCE Omni 1-Dome



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands