background image

Sign Size (mm)

(Height x Length)

Electrical

Supply

VA

Load

900 × 2650

6.6 A

50

900 × 3000

6.6 A

56

900 × 900 Gate

230 VAC

22

1200 × 1200 Gate

230 VAC

32

700 × 1300 Gate

230 VAC

TBD

Electrical Supply

RELIANCE

 Airfield Signs are available in parallel and series versions according to power requirements. RELIANCE

 Gate Signs

are available in parallel only.

Power

Requirements

Constant Current Regulator

(Series system)

2.8-6.6 A, 50/60 Hz

3-7 step CCR

Mains Power System

(Parallel system)

120-240 VAC, 50/60 Hz

Dimensions and Weight

Dimensions are the overall outer dimensions of the sign frame. The visible face of the sign legend panel is 100 mm less than

the height and width of the sign frame. When installed and mounted onto poles and Y-shaped feet, the total sign height

increases by approximately 100 mm.

Sign Size (mm)

(Height x Length)

Weight (kg)

(322 km/h)

Weight (kg)

(480 km/h)

700 x 1150

24.8

24.8

700 x 1300

26.5

26.5

700 x 1600

31.0

35.0

700 x 1800

33.7

37.7

700 x 2100

41.2

41.2

700 x 2500

46.0

50.0

700 x 2650

51.4

51.4

700 x 3000

60.0

60.0

900 x 1150

28.8

33.3

900 x 1300

31.0

35.5

900 x 1600

36.0

44.5

900 x 1800

39.7

48.2

900 x 2100

48.2

52.7

900 x 2500

53.9

62.4

900 x 2650

56.4

64.9

900 x 3000

61.9

66.4

900 x 900 Gate

21.0

N/A

1200 x 1200 Gate

32.5

N/A

700 x 1300 Gate

24.5

N/A

UM-4007, Rev. 6.0, 2022/07/18

11

Copyright 

©

 ADB Safegate, All Rights Reserved

Summary of Contents for RELIANCE Gate Sign











































































Reviews: