ADB Safegate L-858 AGSF Series User Manual Download Page 42

Page: 42 / 56

•

If the lamps do not illuminate and the onboard Green LED (D12) does not flash at a 1 second rate (heartbeat), then there

is a fault on the power supply board or incoming power. Remove the input power and check the input wiring for opens or

shorts.

•

Make certain you replace the cover after you are done checking the power supply.

Figure 15: Halogen Sign Power Supply 44A7199-200 with Cover Removed

Refer to

Table 14

for the power supply LEDs.

Table 14: Halogen Sign Power Supply LEDs

LED

Function

Green (D12)

Flashes at 120 beats per minute when power is applied to the power

supply board.

Red (D13)

Indicates the power supply board assembly is not able to maintain a

regulated lamp current. This also indicates that at least one lamp is

burnt out.

4.3.4 Halogen Lamp Power Supply Connections

If you replace the power supply board, refer to

Table 15

for the power supply board connections. See also

Schematics

. Refer

Checking the Halogen Lamp Sign Power Supply

Table 15: Halogen Sign Power Supply Connections

This connector…

Connects to this device…

P1, P2

A string of up to eight 48 W primary lamps

P3, P4

A string of up to eight 48 W backup lamps

P12, P13

The output of a 6.6 A isolation transformer providing input power for

the halogen sign

P7, P8, P9

Optional lamps-out indicator

L-858 AGSF
Maintenance

32
Copyright

Summary of Contents for L-858 AGSF Series





















































Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands

ADB Safegate L-858 AGSF Series, User Manual

Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands