ADB Safegate L-858 AGSF Series User Manual Download Page 40 | Manualshive

Page: 40 / 56

background image

Problem – Halogen

Possible Cause

Corrective Action

All Lamps are out or not

functioning correctly.

Loose wires or

connections

Tighten or replace wires.

CCR circuit-shorted

Check circuit operation.

Sign ON/OFF switch is

closed.

Check the Sign ON/OFF switch for proper operation. Replace if necessary.

Power supply fault or CCR

is not operating correctly

Remove the cover to observe the power supply board with two LEDs located near

the notch where the wires enter the supply. LEDs are labeled D13 for Red and D12

for Green. When power is first applied, the green LED will flash (several times) first,

followed by the Red LED flashing (several times) lasting about 10 seconds, followed

by a regular green flashing “heartbeat” (at about a one blink per second rate). The

initial x-times flash is for manufacturing purposes and may vary in number from

board to board. When the regular green flashing “heartbeat” flashes, the red LED

may flicker a couple of times until the circuit stabilizes but will extinguish quickly

under normal operating conditions. If the green “heartbeat” is present and the red

LED lights solidly, this indicates that the power supply is good but there is an open

on the output of the power supply (likely either the interconnecting wires or one of

the halogen lamps are burned out). If no status LEDs light or one or both lights

solidly, and power is applied to the input, then the power supply needs to be

1

Light Panels are too dim.

Power supply fault or CCR

is not operating correctly

1

Check the CCR’s output current.

Jumper P6 on Power

Supply is set incorrectly or

missing

Check the P6 jumper setting and compare to chart on

to confirm or

correct placement of the jumper.

CAUTION

Remove power prior to changing jumper settings.

Optional Lamps Out

Indicator continues to

flash after replacing lamps.

There may be another

burnt out lamp.

Verify all lamps are tightly seated and not burnt out.

Power to sign has not

been cycled.

Remove power to sign for at least one minute and then power back up.

Notes

1

If you have a Halogen Sign with the 44A6225/X top-mounted power supply, please see the manual 96A0286 Rev AG on our Web site. If you wish to migrate
the old power supply to the new (44A7199/200) one used in this manual, please call your ADB representative.

Note

There is no jumper setting for changing between 50/60 hz.
There are no jumper settings for backup lamp use.

4.3.3 Checking the Halogen Lamp Sign Power Supply

1

If you have a Halogen Sign with the 44A6225/X top-mounted power supply, please see the manual 96A0286 Rev AG on our Web site. If

you wish to migrate the old power supply to the new (44A7199/200) one used in this manual, please call your ADB representative.

L-858 AGSF
Maintenance

30
Copyright

©

ADB Safegate, All Rights Reserved

«
...
38
39
40
41
42
...
»

Summary of Contents for L-858 AGSF Series

























































Reviews:

No comments

Related manuals for L-858 AGSF Series

Brand: ParaBody Pages: 4

Brand: Raymarine Pages: 90

Brand: Bahco Pages: 9

Brand: AccuMed Pages: 14

Brand: TAS Pages: 25

Brand: Rapid Technic Pages: 152

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: Ultraflex Pages: 3

Brand: Raytheon Pages: 68

Brand: KegLand Pages: 23

Brand: Nabtesco Pages: 26

Brand: Quincy Pages: 31

Lyme FIA Sofia 2

Brand: Quidel Pages: 49

Brand: Quest Leisure Products Pages: 12

Brand: Yanmar Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands