Adaptive Tripp-Lite 1109502801 Replacing Manual Download Page 4

R

EPLACING

 

THE

 B

ILLBOARD

 UPS

4

PN 1109610110 

REV

. A

8.  Connect all previously removed cables.

Figure 6: UPS power and communication connections.

Plug the UPS power cord into the control cabinet’s AC receptacle.

9.  Power on the Billboard and the control cabinet on.

Power on the load center(s) on the back of the Billboard.

Power on the load center on the control cabinet.

Press and hold the UPS On/Off/Standby 

 button until the alarm beeps once 

indicating the UPS load output receptacles are now on.

A

B

C

D

E

F

* Critical components that may require power to be cycled on or off from a remote Internet connection.
** Critical components on dual billboard configurations only, that may require power to be cycled on or off from a remote Internet 
connection.

Item

Port

Component connection

* A

 Load 1

(2 switched outlets)

PC controller #1 power cord label ID #17.

DVI / fiber converter #1 power cord label ID #8.

** B

Load 2

(2 switched outlets)

PC controller #2 power cord label ID #22.

DVI / fiber converter #2 power cord label ID #9.

C

Load 3

(4 unswitched outlets)

For customer’s ISP (Internet Service Provider) equipment.

Y–type power cord label ID #7 connects both camera PoE power 
cords label ID #2 and if applicable #27 into one UPS receptacle.

Router power cord label ID #11.

KVM drawer power cord label ID #12.

E

Ethernet

Ethernet cable label ID #4 from router.

F

Envirosense

Environmental probe (Envirosense) cable label ID #19.

K

USB

PC controller #1 USB cable label ID #28.

Summary of Contents for Tripp-Lite 1109502801







Reviews: