Adaptec PowerDomain 29160N Installation Manual Download Page 12

12

Regulatory Compliance Statements

Federal Communications Commission Radio Frequency Interference Statement

WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. However, if this equipment does cause
interference to radio or television equipment reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connect-
ed.Consult the dealer or an experienced radio/television technician for help.

Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit
to the specified limits of the rules.

This device complies with part 15 of the FCC rules. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.

European Union Compliance Statement

This Information Technology Equipment has been tested and found to comply with the following
European directives:

EMC Directive 89/336/EEC

EN 50081-1 (1992):
EN55022 (1994) Class B

EN 50082-1 (1992):

EN61000-4-2 (1998)

EN61000-4-3 (1998)

EN61000-4-4 (1995)

Adaptec, Inc.

SCSI Card 29160N 

Tested to Comply 

With FCC Standards

FOR HOME OR OFFICE USE

512512final.qxd  12/17/99 2:05 PM  Page 12

Summary of Contents for PowerDomain 29160N















Reviews: