manualshive.com logo in svg

Adaptec ASR-2000S, Installation Manual

Share
Download
Adaptec ASR-2000S Installation Manual Download Page 43

3-8

Adaptec RAID Installation Guide

4

Start up the system. During startup, press Ctrl+A to start 
SMOR. Use SMOR to create the RAID. For details, refer to 

Using SMOR on page 2-10

.

5

Insert the Windows NT CD in the drive and restart the system.

6

When prompted, press Enter to initiate Setup’s mass storage 
detection. Windows NT detects any controllers for which it has 
built-in drivers. Once your other hardware is detected, cancel 
out of any further detection. 

7

Shut down and restart your system.

8

You are prompted to either press S to specify additional 
controllers or press Enter to continue Windows NT installation 
without specifying additional controllers.

Press S to Specify Additional Devices. Select Other, then insert 
the driver disk you created in 

Step 1

.

9

Select Adaptec I

2

O RAID Host Adapter Driver for NT 4.0

.

10

Press Enter and continue with the installation according to the 
instructions in the Windows NT documentation.

Upgrading the Controller in an Existing System

In this scenario, you are removing a controller from a working 
Windows NT 4.0 system and substituting an Adaptec RAID 
controller.

Note: 

If you have already installed an Adaptec RAID 

controller in your system and want to change drivers, refer 
to 

Changing the Driver in an Existing System on page 3-9

 

instead of this procedure.

To install the driver

1

Create a driver floppy disk using the Adaptec RAID Installation CD. 
To create the disk

a

Insert the Adaptec RAID Installation CD in your drive.

b

Boot from the CD. The CD loads a Linux kernel that is used 
to manage all of its functions.

Combined RAID IG.book  Page 8  Thursday, May 3, 2001  11:51 PM

Summary of Contents for ASR-2000S





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands