Adaptec 5325302036 - SANbloc S50 JBOD Hard Drive Array Quick Install Manual Download

Page: 3 / 20

SANBloc S50 Quick Install Guide

SANBloc S50 Quick Install
Guide

The SANbloc S50 JBOD enclosure supports up to 12 Serial Attached SCSI

(SAS), 12 Serial ATA (SATA) disk drives, or a combination of SAS and

SATA drives (up to 12 drives total). A maximum of seven (7) S50s can be

chained to each Snap Server.
This

Quick Installation Guide

describes how to install the SANbloc S50

enclosure and connect it to a 500/600 Series Snap Server.

Note

To connect the SANbloc S50 enclosure, your Snap Server must be

installed with a Serial Attached SCSI (SAS) host adapter.

Summary of Contents for 5325302036 - SANbloc S50 JBOD Hard Drive Array





















Search results

Summary of Contents for 5325302036 - SANbloc S50 JBOD Hard Drive Array

Reviews:

Related manuals for 5325302036 - SANbloc S50 JBOD Hard Drive Array

Brands by name

Popular brands

Adaptec 5325302036 - SANbloc S50 JBOD Hard Drive Array, Quick Install Manual

Search results

Summary of Contents for 5325302036 - SANbloc S50 JBOD Hard Drive Array

Reviews:

Related manuals for 5325302036 - SANbloc S50 JBOD Hard Drive Array

Brands by name

Popular brands