background image

5

3- Introduction

ADAMS  STABILIZER is designed for unstable mains and safety of load.
Mains input and output are written on clemenses. When installing the STABILIZER it
is necessary to use a connection cable of suitable diameter to use the STABILIZER
more effective.
STABILIZER will be shut down automatically when the input voltage goes to out of
limits or one of the phase’s cuts off or short circuit in the output. After the temporary
conditions STABILIZER will start again
If it is requested and allowed to short term fault, STABILIZER will continue to operate
by increasing the delay time. Over the mentioned delay time, STABILIZER will STOP
automatically.
The 3 analog displays, on the front panel of STABILIZER are used to see the
applied voltage and mains input to the unit Input voltage can be checked by the RED
signal lights.
The shut down of the STABILIZER and the transfer of the mains to the output is
done by 1-0-2 REG. switches.

1:   Input bypass to output position

          0:   No voltage applied position.
         2:   Regulator position.

3.1 Preliminary warnings to use the STABILIZER

Automatic Voltage Regulators (STABILIZER) are used to protect the sensitive loads
from the unstable mains and to provide proper operating of the load.

Related points for human health are mentioned in

“Safety Warnings”

 part of this

manual.
In this part, these points will repeated to give information about the connections of
STABILIZER and the load.

•  When installing the STABILIZER to use cable with improper diameter can be

dangerous for user health and safety of the unit.

•  Earth cable should be chosen concerning the current capacity, which is written on

the label on the front panel of the STABILIZER. All units earth connections, which
are connected to STABILIZER, should be done with this earth cable. Without
earth, connection or unproved earth connected units are dangerous for user
health and have high risk of electronic circuit board faults.

Summary of Contents for e-AVR series









Reviews: