background image

Glass BL-ST:: 1221114201/03_661Y3300 • A

Installation

CONNECTING THREE-PHASE 

APPLIANCES

This procedure is to be carried out by an 

approved electrician:

1.  Connect using four conductors of 

2.5 mm

2

, (one green/yellow for the 

earth.)

2.  Connection to the mains via termi-

nals B1, B2 and B3 of the thermo-

stat (see "Figure 3" to "Figure 5", 

page 17).

3.  Connect green/yellow conductor 

to terminal    

4.  For a 400 V Tri supply without 

neutral, modify the internal con-

nections  by following the wiring 

diagram in "Figure 3", page 17.

5.  Regarding a 230 V Tri connection, 

see diagram in "Figure 4", page 17.

CONNECTING SINGLE PHASE 

APPLIANCES

This procedure is to be carried out by an 

approved electrician:

1.  Use three conductors of 2.5 mm

2

(one green/yellow for the earth).

2.  Connect to the mains via terminals 

A and B or 1 and 2 of the thermo-

stat (see page 16).

3.  Connect the green/yellow conduc-

tor to terminal   

Essential instructions for the electrical safety

•  The protection class of the appliance is: I.
•  The covers closing the electric group provide protection against the 

involuntary touching of the active electric parts under voltage.

•  Connection to the mains is to be carried out in accordance with the 

installation diagram found in this installation manual and on the plate 

at the bottom of the appliance, by paying attention to the connection 

to the correct phases.

•  It is FORBIDDEN AND DANGEROUS to start-up the appliance without 

the professional installation by a specialist provided with protection 

against the electric contacts.

•  For the correct operation of the appliance, we recommend the use of a 

protection relay in the mains of your building. 

•  CAUTION! Before doing any maintenance or repair tasks, disconnect 

the appliance from the electric supply. The maintenance and repair 

works have to be carried out by qualified personnel.

•  After repair and maintenance works, the appliance has to be restored 

to its original condition.

•  The repair works must be documented by the technician in order to 

preserve the validity of the warranty.

15

EN

Summary of Contents for GLASS BL 100





























Reviews: