background image

EN • 3

662Y0600 • A

E

N

FR

R

U

P

L

DE

IT

ES

N

L

Warnings

CERTIFICATION

The products have received 

CE

 certification in accordance with the standards 

in force in various countries (European Directives 

92/42/EEC

 "efficiency 

requirements", 

2009/142/EC

 "gas appliances").

IMPORTANT NOTES

If you smell gas :

-  Isolate the gas supply immediately.
-  Ventilate the room (Open the windows).
-  Do not use electrical appliances and do not operate switches.
-  Notify your gas supplier and/or your installer immediately.

These instructions are an integral part of the equipment to which they relate and 
must be left for the user.

The product is to be installed and serviced by qualified technicians, in accordance 
with current regulations.

The manufacturer declines all liability for any damage caused as a result of 
incorrect installation or in the event of the use of appliances or accessories that 
are not specified by the manufacturer.

  The manufacturer reserves the right to change the technical 

characteristics and features of its products without prior 
notice.

  The availability of certain models as well as their accessories 

may vary according to markets.

WHO SHOULD READ THESE INSTRUCTIONS

These instructions should be read by:
- the design engineer/consultant
- the user
- the installer
- the service engineer

SYMBOLS

The following symbols are used in this manual:

RECOMMENDATIONS

 

•  Carefully read this manual before installing and bringing the boiler 

into service.

•  It is prohibited to modify the interior of the appliance in any way, 

without the manufacturer’s prior written agreement.

•  The product must be installed by a qualified engineer, in accordance 

with the applicable local standards and codes.

•  Failure to follow the instructions describing test operations and 

procedures could result in personal injury or a risk of environmental 
pollution.

•  In order to ensure the appliance operates safely and correctly, it is 

important to have it serviced by an approved contractor.

•  If there is a problem please contact your contractor for advice.

• In spite of the strict quality standards that ACV applies to its 

appliances during production, inspection and transport, faults may 
occur. Please notify your approved contractor immediately of any 
faults.

•  Defective parts can only be replaced with original factory parts.

 

•  Before carrying out any work on the boiler, it is important to isolate 

the electrical supply to the unit.

•  The user must not attempt to gain access to the components inside 

the boiler or the control panel.

• This appliance is not intended for use by persons with reduced 

physical, sensory or mental capacities , or lack of experience and 
knowledge (including children) , unless they have been supervised or 
instructed concerning use of the appliance by a person responsible 
for their safety.

Essential instruction for the safety of 
persons and the environment

Electrocution hazard: 
use a qualified technician

Essential instruction for the correct 
operation of the installation

Summary of Contents for BG 2000-S 100





















Reviews: