background image

 

Page 

11

 of 

13

 

 

16.

 Check Voice System Interaction

  

 Audio System and ODMD 

1.  Press and release the Talk button. 

 

2.  When you hear the voice portal prompt, wait for the beep and say “Audio.”  

3.  After your command is accepted, wait for the beep and say “SXM.” 

4.  After your command is accepted, wait for the beep and say “Channel 122.” You should see channel 

122

 on the 

ODMD.  

 Climate Control System 

1. Select 

AUTO

 to turn on the climate control system. 

2.  Press and release the Talk button. 

3.  When you hear the voice portal prompt, wait for the beep and say “Climate control.” 

4.  After your command is accepted, wait for the beep and say “Temperature max cool.” The climate control should 

come on in response. 

17.

 Check 

Bluetooth

® 

HandsFreeLink

®

 (HFL) 

To ensure HFL works and is ready to use, start the engine, turn on the audio-navigation unit, then press and hold the  
Hang-up/Back button on the steering wheel for about 

5 seconds

. You should hear “The HFT is OK.” If you do not hear 

this message, see the service information for troubleshooting information.  

If you want to pair a phone, touch the PHONE button below the ODMD. 

NEW MODEL SERVICE INFORMATION 

1.

 10-Speed Transmission

 

This vehicle comes with a 10-speed automatic transmission.   

2.

 Traffic Jam Assist (TJA)

 

This vehicle comes with TJA. It uses a radar sensor mounted inside the front grille, along with a windshield-mounted 
camera, to detect and monitor lane lines as well as any vehicle ahead. In heavy traffic, with the Adaptive Cruise Control 
with Low Speed Follow on, it will adjust the vehicle speed to keep a set interval with the vehicle ahead and apply 
steering torque to keep the vehicle centered in the lane. See the online owner’s manual for details.   

3.

 Shift by Wire (SBW)

 

You select gears by either pressing or pulling up on each of the SBW shifter assembly buttons. Park, Neutral, and Drive 
are all activated by pressing 

down

 on the corresponding letter. Reverse is activated when you pull 

up

 on the button. 

Colored indicators next to each button tell you which gear is selected. 

Shifting from Park to Reverse, Park to Drive, Neutral to Reverse, and Neutral to Drive can only be done with the brake 
pedal applied. 

 

Summary of Contents for RLX 2018














Reviews: