New Key Fob/Lost Key Fobs
5
IIff yyo
ou
u c
ca
an
n d
diissa
arrm
m tth
he
e ssyysstte
em
m -- iie
e;; yyo
ou
u h
ha
avve
e a
a
w
wo
orrkkiin
ng
g ffo
ob
b a
an
nd
d n
ne
ee
ed
d tto
o a
ad
dd
d a
an
no
otth
he
err;;
1.
Switch ignition off
2.
Disarm the system from the fob
3.
NOTE Sections 4 and 5 must be completed
within 10 seconds
4.
Switch the ignition on-off 5 times in quick
succession, leaving the ignition ON at the 5th
action
5.
Change the state of the accessory switch
circuit - WHITE wire (ie; connect to ground if
not connected and vice versa) The unit will
beep once and enter learn mode
6.
Press and hold the Lock button until the unit
beeps then release it
7.
The unit will beep twice
8.
Press and hold the Lock button again and the
unit will beep three times.
IIff tth
he
e ssyysstte
em
m iiss d
diiss--a
arrm
me
ed
d b
bu
utt yyo
ou
u d
do
on
n’’tt h
ha
avve
e a
a
w
wo
orrkkiin
ng
g ffo
ob
b ((yyo
ou
u h
ha
avve
e llo
osstt a
allll w
wo
orrkkiin
ng
g ffo
ob
bss));;
1.
Switch off the scooter ignition
2.
Remove alarm fuse
3.
Leave for 5 minutes
4.
Reconnect alarm fuse (and within 10 seconds
perform sections 5 & 6)
5.
Switch the ignition on-off 5 times in quick
succession, leaving the ignition ON at the 5th
action
6.
Change the state of the accessory switch
circuit - WHITE wire (ie; connect to ground if
not connected and vice versa) The unit will
beep once and enter learn mode
7.
Press and hold the Lock button until the unit beeps
then release it
8.
The unit will beep twice
9.
Press and hold the Lock button again and the
unit will beep three times
IIff tth
he
e ssyysstte
em
m iiss a
arrm
me
ed
d a
an
nd
d yyo
ou
u d
do
on
n’’tt h
ha
avve
e a
a
w
wo
orrkkiin
ng
g ffo
ob
b ((yyo
ou
u h
ha
avve
e llo
osstt a
allll w
wo
orrkkiin
ng
g ffo
ob
bss));;
1.
Ensure the scooter ignition is switched off.
2.
Remove the alarm fuse
3.
Leave for 5 minutes
4.
Replace the alarm fuse - the alarm will sound
for 30 seconds (unless the system has sounded
10 times for power loss in which case there will
not be an audible reaction but wait 30 seconds)
Ensure the ignition is OFF during this time and
ensure the alarm is not triggered by accessory
switch or movement
5.
Trigger the alarm by turning ON the ignition.
When the alarm sounds turn the ignition OFF.
When the siren stops after 30 seconds (ie;
during the quiet time) you have 10 seconds to
perform steps 6 & 7
6.
Switch the ignition on and off 5 times, leaving
the ignition ON at the fifth action
7.
Change the state of the accessory switch
circuit - WHITE wire (ie; connect to ground if
not connected and vice versa) The unit will
beep once and enter learn mode
8.
Press and hold the Lock button until the unit beeps
then release it
9.
The unit will beep twice
10. Press and hold the Lock button again and the
unit will beep three times.
NEW/REPLACEMENT/UPGRADED KEY FOBS CAN BE ORDERED
DIRECT FROM ACUMEN
www.acumen-electronics.co.uk
Summary of Contents for 51020
Page 1: ......
Page 8: ...Wiring Diagram ...
