background image

TIMER OFF Button

12

13

10

11

Used to select the fan speed in four steps:

AUTO

LOW

MED

HIGH

FAN SPEED Button

Press this button to initiate the auto-off time

sequence. Each press will increase the auto-

timed setting in 30 minutes increments. When

the setting time displays 10H, each press will

increase the auto-timed setting 60 minutes

increments. To cancel the auto-timed program,

simply adjust the auto-off time to 0:0

8

7

When you press the recessed RESET button,

all current settings are cancelled and the

control will return to the initial settings.

RESET Button:

Push this button to decrease setting temperature

in a range of 17 C~30 C.

O

O

UP Button (

)

Push this button to increase setting temperature

in a range of 17 C~30 C.

O

O

DOWN Button (

)

14

LOCK Button

When you press the recessed LOCK button,

all current settings are locked in and the

remote controller does not accept any

operation except that of the LOCK. Press

again to cancel the LOCK mode.

Buttons design might be slightly

different from the actual one you

purchased depending on individual

models.

NOTE:

Activate / Disable TURBO function. If pressed

m

for

ore than 2 seconds, the SELF CLEAN

function will be activated, pushing more than

2 seconds again to disable.

TURBO/SELF CLEAN Button:

,

,

LED / FOLLOW ME Button

Disable/Active indoor screen Display. When

pressed for more than 2 seconds, the

FOLLOW ME function will be activated. Press

again for more t

n 2 seconds to disable.

,

,

1

2

4

5

1

2

4

5

3

9

10

8

6
7

11

12

13

14

M ODE

SWING

TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOCK

LED

FOLLOWME

TIMER

ON

TURBO

SEL FCLEAN

DIRECT

SLEEP

3

9

10

8

6

7

11

12

13

14

MODE

SWING

TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOCK

LED

FOLLOWME

TIMER

ON

TURBO

SELF CLEAN

DIRECT

SLEEP

SHORTCUT Button

Used to restore the current settings or resume

previous settings.

When power is connected for the first time, select

the SHORTCUT button.The unit will operate on

AUTO mode, 24 C, and fan speed is Auto.

When this button is selected remote controller is on,

the system will automatically revert back to the

previous settings including operating mode,

setting temperature, fan speed level and sleep

feature (if activated). And transmit the signals to

the unit.

When this button is selected remote controller is off,

the system will only resume the previous settings

and will not transmit the signals to the unit. And

the sleep feature is disabled.

When you press button for more than 2 seconds,

the system will automatically restore the current

operation settings including operating mode, setting

temperature, fan speed level and sleep feature

(if activated ).

O

9

O N / O F F

O N / O F F

Summary of Contents for SWB26C/E









Reviews: