background image

STORAGE

Store the 

AeroPilates  Pro XP557

 in a clean, dry place.

It is recommended that two people be available to move the 

AeroPilates  Pro XP557.

To move the 

AeroPilates  Pro XP557:

  First, attach one of the 

TENSION SPRINGS

 to the 

EYEHOOK

(22)

 to prevent the 

CARRIAGE(26)

 from moving. Second, grasp the 

PULLEY POST(39)

 and lift the unit

from the back. Third, roll the 

AeroPilates  Pro XP557

 on the moving wheels that are attached to the

FRONT LEG(2).

1.
2.
3.

MAINTENANCE

The safety and integrity designed into the 

AeroPilates  Pro XP557

 can only be maintained when the

AeroPilates  Pro XP557

 is regularly examined for damage and wear.  Special attention should be given to

the following:

It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Worn or damaged components should be replaced immediately or the 

AeroPilates  Pro XP557

 removed

from service until repair is made.
Verify that the Warning Label is present and legible. Replace the Warning Label if it is missing or
damaged.
Verify that the 

ROPES(44)

 are properly installed on the 

PULLEY SETS(41).

Check the condition of the 

ROPES(44)

 and replace if they are frayed or worn.

Check the 

PLASTIC SNAP HOOKS(45)

 on the ends of the 

ROPES(44). 

Replace the 

ROPES(44)

 if

PLASTIC SNAP HOOKS(45)

 are damaged or deformed.

Check the condition of the 

TENSION SPRINGS(31, 32).

 Replace the springs that are damaged.

Check the 

BUNGEE CORD(51)

 on the 

CARDIO REBOUNDER(49)

 for wear. Replace the 

CARDIO

REBOUNDER(49)

 if the 

BUNGEE CORD(51)

 is frayed or worn.

Check the 

PULLEY SETS(41)

 for excessive wear. Replace worn 

PULLEY SETS(41).

Check the 

HAND STRAPS(46)

 for damage. Replace damaged parts.

Check the 

FOAM SLEEVE(18), FOAM PADS(37),

 and 

FOAM PAD WEAR COVERS(84)

 and replace

if damaged or worn.
Check the 

STOP PLATES(23, 24)

 for looseness or damage and replace any damaged parts.

Check the 

CUSHION(29)

 and replace if it is damaged or worn.

Check and clean the 

ROLLERS(27)

 and the rolling surfaces on the rails. Clean by wiping with a dry

cloth.
Only Stamina Products supplied components shall be used to maintain/repair the 

AeroPilates  Pro

XP557.

Keep your 

AeroPilates  Pro XP557

 clean by wiping with an absorbent cloth after use.

1.
2.

3.

4.
5.
6.

7.
8.

9.

10.
11.

12.
13.
14.

15.

16.

13

Summary of Contents for Aero Pilates Pro XP557


















Reviews: