background image

6

3

Assembly

1. Remove all parts from the shipping container(s).  

Remove all packing material from the parts. Recycle 

shipping and packing materials in accordance with the 

recycling codes of your location.

Move the side frames apart and pull forward on the Fold 

Frame Pull Pin until the fold frame locks into place

2. Place the front seat snap brackets onto the front seat 

support tubes and than place rear seat snap brackets 

onto the rear seat support tubes.
Make sure that the seat is square, and all 4 corners are 

snapped into place before sitting on chair.

 

3. Loosen then remove the self-locking nut and screw that 

are in the chair frame where the back assembly will be 

attached and set aside.  

 

Tools required for setup: 3/4" wrench, 3/4" socket wrench, 7/16" wrench, 

#10 metric wrench, 5/32" hex key 

Fold Frame Pull Pin

10. If the height-adjustable armrests were ordered, 

remove the two hex bolts in the clamp of the armrest 

clamp assembly. 

11. Place armrest and armrest clamp onto the back frame 

as shown. Insert the hex bolt and hand start two bolts into 

the clamp. 

12. Place armrest and armrest clamp 8 1/4" from the top 

of the frame and tighten bolts securely.
Repeat steps 6-12 for the other armrest.

Front Snap Bracket

Rear Snap Bracket

Summary of Contents for 922
















Reviews: